(h)  
Tighten the checknut to 350-400 pound-inches.

 (i)  
Install the lockwire on the checknut and the locking key.

 (j)  
Apply a bead of sealant to the rod end checknut.

 (k)  
Supply the systems A and B hydraulic power (Ref 27-61-00/201).

 (l)  
Move the speed brake lever to the DOWN position to lower the spoilers if it is necessary.

 (m)  
Install the trailing edge access panel if you lowered the flaps.

 (n)  
Move the flap control lever to the UP detent to lift the flaps if it is necessary.

 (o)  
Measure the clearance between the spoiler and the flap again.

 S 725-010
 (3)  
Do the flight spoiler functional test.

 F.
Put the Airplane Back to Its Usual Condition

 S 865-011
 (1)
Remove the systems A and B hydraulic power (Ref 27-61-00/201).

 S 865-012

 (2)  
Remove the electrical power (Ref 24-22-00/201).

 TASK 27-61-11-725-002
 3. Flight Spoiler Functional Test
______________________________
 A. Special Tools and Equipment
 (1)  
4MIT65B80307-1 Control Surface Protractor

 (2)  
F71292-17 Control Surface Protractor Stand Assembly

 B.
References

 (1)  
24-22-00/201, Manual Control

 (2)  
27-61-00/201, Spoiler Control System

 C.
Access

 (1)  
Location Zone 101, 102 Control Cabin 307, 407 Wing Trailing Edge Outboard Flaps and Spoilers

 D.
Procedure

 NOTE: This procedure makes sure all all of the flight spoilers move to
____ the limit of their travel. If you replaced a spoiler panel, it is only necessary to do the test for that spoiler.
 S 865-013
 (1)  Supply the electrical power (Ref 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-11
 ALL  ú ú 02 Page 504 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (2)  S 865-014Supply the systems A and B hydraulic power (Ref 27-61-00/201).
 (3)  S 485-015Install the protractor stand and the control surface protractor on the spoilers.
 NOTE:____ You can use a hand held protractor on the spoiler.
 (4)  S 485-016Install the protractor mount and the protractor on the captain's aileron control wheel.
 (5)  S 825-017Set the protractor to zero.
 (6)  S 725-018Move the speed brake lever to the UP position.
 (7)  S 725-019Move the captain's aileron control wheel in the neutral position. (a) Make sure the spoiler No. 2 is up 39 |3 degrees. (b) Make sure the spoiler No. 3 aligns with the spoiler No. 2 in the limit of |0.25 inch. (c) Make sure the spoiler No. 6 is up the same as the spoiler No. 2 in the limit of |2 degrees (d) Make sure the spoiler No. 6 is up a minimum of 36 degrees. (e) Make sure the spoiler No. 7 aligns with the spoiler No. 6 in the limit of |0.25 inch.
 (8)  S 865-020Move the speed brake lever to the DOWN position to lower the spoilers.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-11
 ALL  ú ú 01 Page 505 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 E. Put the Airplane Back to Its Usual Condition
 S 865-021
 (1)
Remove the systems A and B hydraulic power (Ref 27-61-00/201).

 S 865-022

 (2)  
Remove the electrical power (Ref 24-22-00/201).

 S 085-023

 (3)  
Remove the protractor and the protractor mount from the control wheel.

 S 085-024

 (4)
Remove the protractors and the protractor stands from the spoilers.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(42)