56-11-21
ALL ú ú B01 Page 406 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 954-021-B00
(4) Remove a strip of the masking tape immediately on top of the space at the outer edge of the window.
NOTE:____Use a sharp knife for this procedure. The result will be strips of masking tape that gives protection to the edges of the outer space between the window and the skin.
S 434-022-B00
(5) Put a clean dry nylon cord in the bottom of the space at the outer edge of the window.
NOTE: The cord must be longer than the distance around the edge of
____ the window. The ends of the cord must overlap approximately
0.5 inch with the ends in the upper aft corner.
S 394-023-B00
(6) Use a flow gun or a spatula to apply the aerodynamic smoother into the space until it is fully filled.
NOTE: Smoother is available in different work lives that are
____ satisfactory for a number of tasks. You must apply the smoother during the applicable work life. Do not let air get mixed in below the smoother.
S 034-024-B00
CAUTION: WHEN YOU APPLY THE SMOOTHER, BE CAREFUL THAT YOU DO NOT MAKE
_______ SCRATCHES ON THE METAL OR GLASS SURFACES. ALSO, DO NOT MAKE THE METAL OR THE GLASS SURFACES ROUGH WHEN YOU APPLY THE SMOOTHER.
(7)
Remove all the unwanted filler while it is wet, until it is level with the masking tape.
S 954-025-B00
(8)
Remove the masking tape from the edges of the space and the plastic layer from the outer surface of the window.
NOTE: You can make the material that lifts up at the edges of the
____
clearance smooth.
G. Put the Airplane Back to Its Usual Condition
S 414-031-B00
(1) Install the trim panels and the crash padding where it is necessary (AMM 25-11-21/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
56-11-21
ALL ú ú B01 Page 407 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 954-032-B00
(2) Remove the plastic layer from the inner surface of the window.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
56-11-21
ALL ú ú B03 Page 408 ú Mar 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
WINDOW NO. 3 - INSPECTION/CHECK
_______________________________
1. General_______
A. A window which has an unsatisfactory visual condition must be replaced.
(1) Different types of window damage are specified below:
(a)
Crazing: Crazing is a number of very small cracks perpendicular to the surface of the plastic. Because of the very small width of the cracks, crazing is not easy to see when you look directly at the surface. You can see crazing by a reflection of the smooth surfaces of the cracks, at different angles to the light.
(b)
Crack: A crack has width which you can see when you look directly at the surface. A crack can become larger in any direction. The angle that the crack becomes larger depends on the direction of the force. A crack in the stretched acrylic can have chevron or clamshell growth lines (Fig. 601). A crack will become larger from a stressed area such as a scratch or crazing.
(c)
Scratch: A scratch is the removal or movement of material from the surface of the window along a line. The depth and width are usually small.
(d)
Chips:
1) Spall (shell type) chips have a circular or rounded outer edge. There are many small ridges that follow the shape of the outer edge. The ridges become smaller at the center or the deepest point of the chip, similar to a clamshell.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 WINDOWS(26)
