S 144-013-B00
(3)
Make the surfaces on the plug and window frame dry with a clean cheesecloth which does not contain lint or oils.
F. Install the Plug
S 434-014-B00
(1)
Install the seal on the plug if you removed the seal.
S 414-015-B00
(2)
Install the plug with the seal in the window frame.
S 434-016-B00
(3)
Install the window retaining clips and clip adjusting screws (10 locations). Tighten each clip adjusting screw from 12 to 15 pound-inches.
(a) If the window retaining clip is loose or is not in the correct position, do these steps: 1) Put the window retaining clip in its position. 2) Tighten the clip adjusting screw in increments of 5
pound-inches. Continue to tighten the window retaining clip until it is not loose and it is installed in the correct position.
S 434-017-B00
(4) Connect the grounding strap to the plug.
S 354-021-B00
CAUTION: DO NOT CUT THE PLUG WHEN YOU CUT THE DIAPHRAM ON THE SEAL.
_______
THIS CAN CAUSE DAMAGE TO THE PLUG.
(5)
Cut the diaphram on the seal at the line with a notch.
(6)
Install the insulation pillow.
S 414-020-B00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
56-21-11
ALL ú ú B01 Page 404 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 414-018-B00
(7) Install the sidewall panel (AMM 25-21-46/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
56-21-11
ALL ú ú B01 Page 405 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
EMERGENCY EXIT HATCH WINDOW - DESCRIPTION AND OPERATION
_______________________________________________________
1. General_______
A. The emergency exit hatch window, installed in each emergency exit hatch in the passenger cabin, is located in the upper portion of the hatch and is similar in external appearance to the passenger windows (Fig. 1). The window consists of outer and inner panes and an inner-most plastic pane. The inner-most pane is nonstructural and is mounted in the emergency exit hatch trim panel (AMM 52-21-12/401, Emergency Exit Hatch Lining). The outer and inner panes are each capable of taking the cabin full pressurization load. All three panes are acrylic, the structural panes being formed to improve resistance to crazing.
B. Each emergency exit hatch window is designed as a plug type window subject only to the pressure acting on it. The outer window pane of stretched acrylic plastic is rectangular in shape with rounded corners and a routed outer edge to fit the window outboard frame. The pane is curved to fair with the fuselage contour. The inner window pane is made of modified acrylic sheet. It is shaped similarly to the outer pane, but with an unbeveled edge which is seated on the window inboard frame.
C. The outer pane has a peripheral seal of molded synthetic silicone rubber. An outer pane spring assembly and ten outer pane spring retainers secure the outer pane in position on the window outboard frame. The inner pane is pressure sealed to the window inboard frame and outer reveal and is secured by screws which are spaced around the periphery of the window retainer.
D. The emergency exit hatch window is designed to preclude fogging and frosting by means of multiple pane construction with intervening cavities essentially isolated from cabin interior air conditions.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 WINDOWS(58)
