radius during the installation. Be careful with the pane when it is out of the airplane.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-31-00
 ALL  ú ú B01 Page 601 ú Jul 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (d)  Chips:
 1)  Spall (Shell Type) chips have a circular or rounded outer edge. There are many small ridges that follow the shape of the outer edge. The ridges become smaller at the center, or the deepest point of the chip, similar to a clamshell.
 2)  Vee shaped chips have a sharp "V" shape and apparently move into the plastic.
 (e)  Delamination (in-plane crack): A smooth surfaced crack, or a number of cracks, parallel to the window pane surface. An in-plane crack can occur in stretched acrylic and starts at the edges of the pane. A delamination can also occur because of a damaged pane. You can find a delamination from the reflection of the light from the smooth surfaces of the crack. 1) The procedure used to make acrylic panes, causes a lower
 shear strength parallel to the pane surface than that perpendicular to the surface. Because of this, the acrylic acts as a lamination. A delamination is a separation of adjacent layers parallel to the pane surface. It can be induced by a blow with a sharp instrument on the pane edge and usually accompanies deep penetrations into the pane surface. Fine, continous delaminations are specified as crazing.
 2)  Large delaminations in the routed radius are more dangerous than a crazing. This is because the procedure used to make the pane, decreases the ability of the acrylic to resist delaminations parallel to the direction of stretching.
 3)  The peripheral seal on the outer pane can help prevent damage which can cause a delamination. If you find delaminations in the routed radius, examine the window frame for sharp points and the general fit of the pane in the frame.
 B.  Equipment
 (1)  Optical Micrometer - Model 966A or 966A1
 Monocle Industries

 P.O. Box 2426
 Coppell, Tx. U.S.A. 75019
 Tel (214) 393-9920
 Fax (214) 393-9926

 C.  References
 (1)  
56-31-00/401, Door Mounted Windows

 (2)  
56-21-00/801, Door Mounted Windows

 D.  Access
 (1)  Location Zone
 105 Forward Entry Door
 106 Forward Galley Service Door
 110 Aft Entry Door
 112 Aft Galley Service Door

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-31-00
 ALL  ú ú B01 Page 602 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 E. Examine The Door Mounted Windows
 S 216-002-B00
 (1)  Examine the window seals for deterioration.
 NOTE: Replace the window seals if it is necessary
____
 (Ref 56-31-00/401).

 S 216-003-B00
 (2)  
Examine the window for marks, scratches, and dents in the plastic reveal.

 S 216-004-B00

 (3)  
Examine the window for loose fasteners.

 S 216-005-B00
 CAUTION: DO NOT PRESSURIZE THE AIRPLANE IF A MIDDLE PANE HAS CRACKS OR
_______
 CRAZING. THE PRESSURE CAN BREAK THE WINDOW.

 (4)  Examine the windows for cracks and crazing.
 NOTE: Replace the window pane if the cracks or crazing are out of
____
 these limits (Ref 56-31-00/401).

 (a)  Surface crazing in the outer pane is permitted if it is in these limits and not at the routed edge:
 NOTE: It is not easy to measure the depth of a crazing but
____ this procedure gives the approximate depth. Hold a scale perpendicular to the surface where the crazing is the deepest. View the scale at an approximately 45 degree angle. Multiply the apparent depth by two to get the actual depth (Fig. 601).
 1) A crazing with a 0.060 inch maximum depth in an area less than 2 inches in diameter. 2) A crazing with a 0.050 inch maximum depth along the full surface of the window.
 (b)  Routed Radius Crazing
 NOTE: It is not necessary to remove the pane to examine it for
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 WINDOWS(65)