56-11-31
 ALL  ú ú B01 Page 402 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (2)  S 034-003-B00Remove the trim panels and the crash padding where it is necessary (AMM 25-11-21/201).
 (3)  S 034-004-B00Disconnect the power leads at the bus bar terminals on the window if applicable.
 (4)  S 034-005-B00Remove the thermal switch and the bracket (11) from the window frame (10) if applicable (Fig. 404) (AMM 30-41-31/401).
 (5)  S 034-006-B00Remove the aerodynamic smoother from clearance around the external edge of the window.
 NOTE:____ You can use the nylon cord to make this step easier. The free end of the cord is installed in the upper aft corner of the window. Do not cover the cord end. Pull the cord end until the cord and the smoother are removed (Fig. 402). 

OUTER FUSELAGE

Window Gap Filler Removal
Figure 402

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-11-31
 ALL  ú ú B02 Page 403 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D. Procedure - Remove Window No. 4 or No. 5
 S 034-007-B00
 (1)  Remove these components from the window assembly (1) and the window frame (10).
 NOTE: These steps can be made simple in the area of the map light.
____ This can be done if you remove the map light house first then you remove the lamp.
 (a)  
The self-locking nuts (7)

 (b)  
The flat washer (6, if installed)

 (c)  
The flat washer (5)

 (d)  
The O-ring (4)

 (e)  
The retaining bolt (3).

 S 034-008-B00
 (2)  
Apply hand pressure to the outer side of the window assembly (1) to break the seal.

 S 024-047-B00

 (3)  
Remove the window from the window frame (10).

 NOTE:____Always apply pressure to the largest area possible. You can hit the window lightly with a rubber mallet and a nonmetallic block if it is not particularly easy to remove. The aluminum spacer (2) and pressure seal (9) are removed with the window.
 S 034-009-B00
 CAUTION: BE CAREFUL WHEN YOU REMOVE THE METAL OR THE FAIRING
_______ COMPOUND. IF YOU ARE NOT CAREFUL, DAMAGE TO THE METAL OR TO THE FAIRING COMPOUND ON THE INBOARD FACE OF THE WINDOW FRAME CAN OCCUR.
 (4)  Remove the remaining aerodynamic smoother from the window frame (10) carefully and do not cause damage to the fairing compound (8).
 TASK 56-11-31-404-040-B00
 3.  Window No. 4 or No. 5 Installation (Fig. 403 or 404)__________________________________
 A. Standard Tools and Equipment
 (1)  Spatula or flow gun.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-11-31
 ALL  ú ú B01 Page 404 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

O-RING
EXAMPLE OF THE FASTENER INSTALLATION ON EACH EDGE OF WINDOW NO. 4
NOTE: RETAINING BOLT AND WINDOW FRAME NOT
A SHOWN TO MAKE THE ILLUSTRATION MORE CLEAR.

1
SPACER: MAKE FROM A 2024-T3 WW-T-785 ALUMINUM
TUBE, 5/16 INCH OD BY 0.035 INCH WALL THICKNESS.
THE TUBE MUST BE FROM 0.95 INCH STOCK LENGTH.
REFER TO SECTION A-A FOR HOW TO ASSEMBLE. FOR A
PROTECTIVE FINISH APPLY SULFURIC ACID AND ANODIZE
TO AGREE WITH THE SPECTIFICATIONS OF MIL-A-8625
TYPE II OR CHEMICAL TREAT PER MIL-C-5541, PLUS
ONE LAYER OF BMS 10-11, TYPE I, PRIMER.

Window No. 4 Installation Figure 403
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-11-31
 ALL  ú ú B01 Page 405 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEEA
1. WINDOW NO. 5  ASSEMBLY
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 WINDOWS(32)