21-58-11
ALL ú ú 03 Page 204 ú Feb 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
GROUND EXHAUST VALVE - REMOVAL/INSTALLATION
___________________________________________
1. General_______
A. This procedure has instructions to remove and install the ground exhaust valve. This procedure also has instructions to remove and install the ground exhaust valve actuator. You may remove the actuator without removing the ground exhaust valve from the airplane. The valve is installed below the floor at station 550 of the forward cargo compartment.
TASK 21-58-12-004-001
2. Ground Exhaust Valve Removal (Fig. 401)____________________________
A. Standard Tools and Equipment
(1) Knife, Plastic (Nonmetallic)
B. References
(1)
24-22-00/201, Manual Control
(2)
IPC 21-58-12 Fig. 1
(3)
WDM 21-58-16
(4)
SSM 21-58-06
C. Access
(1) Location Zone 122 Forward Cargo Compartment Forward Half, RH
D. Prepare for the Removal
S 864-002
CAUTION: DO NOT OPERATE THE ELECTRICAL/ELECTRONIC EQUIPMENT WHEN YOU DO
_______ THIS PROCEDURE. IF YOU OPERATE THE ELECTRICAL EQUIPMENT WHEN THE EQUIPMENT COOLING SYSTEM IS OFF, YOU CAN CAUSE THE ELECTRICAL EQUIPMENT TO BECOME TOO HOT.
(1)
Remove the electrical power (AMM 24-22-00/201).
(2)
Remove the moisture shroud from the valve.
(3)
Disconnect the electrical connector, DV447 (10), from the valve (9).
(4)
Disconnect the bonding jumper (11) from the valve (9).
S 034-029
S 034-003
S 034-004
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-58-12
ALL ú ú 02 Page 401 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
9. ELECTRICAL VALVE CONNECTOR SEE A GROUND EXHAUST VALVE 10. HOUSING DRIVE ADAPTER ACTUATOR 4. DUCT DUCT
AIRCRAFT SKIN FLOW
GASKET8.
5. COUPLING
O-RING
CONNECTION ELECTRICAL ADAPTER ACTUATOR A B 11. BONDING JUMPER FWD
COLLAR DRIVE MANUAL OVERRIDE MANUAL B 7. A BOLT SCREW (4 LOCATIONS) WASHER (3 LOCATIONS) BOLT (14 LOCATIONS) BONDING LUG ACTUATOR ROTARY (EXAMPLE, BOLT HOUSING 15 LOCATIONS) 6. 2. 1.
GROUND EXHAUST VALVE
A GASKET FLANGE VALVE GROUND EXHAUST VALVE
AIRPLANE FWD SEALING
SKIN COMPOUND
A-A
Equipment Cooling Ground Exhaust Valve - Installation
Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-58-12
ALL ú ú 01 Page 402 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F54481
A
747-400
MAINTENANCE MANUAL
C-C
Equipment Cooling Ground Exhaust Valve - Installation
Figure 401 (Sheet 2)
B33837
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-58-12
ALL ú ú 02 Page 403 ú Feb 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 144-005
(5)
Use the knife to cut the aerodynamic seal on the outer surface of the valve.
S 034-006
(6)
Remove the bolts (6 and 7) from the outer side of the airplane.
(a) Make a record of where the short bolt (6) is installed.
S 034-007
(7)
Remove the coupling (5) from the top of the valve (9).
S 024-026
(8)
Remove the valve (9).
S 034-027
(9) 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AIR CONDITIONING 2(105)
