E/E Cooling Inboard Valve Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-58-04
 ALL  ú ú 01 Page 402 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
RUBBER SLEEVE
CLAMP
VALVE CLAMP RUBBER SLEEVE
A
747-400
MAINTENANCE MANUAL

CLAMP
RUBBER SLEEVE
CLAMP
RUBBER SLEEVE
MOISTURE SHROUD
VALVE
VELCRO TAPE CONNECTOR
BONDING
MANUAL
JUMPER
DRIVE SCREW NUT WASHER
C
RUBBER
SLEEVE

ELECTRICAL
VALVE
CONNECTOR

CLAMP
BONDING
JUMPER

RUBBER SLEEVE
CLAMP
SCREW
NUT

MANUAL WASHER
DRIVE SCREW NUT ELECTRICAL BONDING
WASHER CONNECTOR JUMPER
D E
E/E Cooling Inboard Valve Installation
Figure 401 (Sheet 2)

B31873
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-58-04
 ALL  ú ú 02 Page 403 ú Feb 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 014-003
 (2)  To get access to the inboard supply valve or the bypass valve, remove the left sidewall lining in the forward cargo compartment at STA 580 (Ref 25-52-01/401).
 D. Remove the Valve
 (1)  S 344-062Remove the moisture shroud from the valve (inboard exhaust valve).
 (2)  S 034-004Disconnect the electrical connector from the valve. (a) Supply valve DV444 (b) Exhaust valve DV445 (c) Bypass valve DV446
 (3)  S 034-005Disconnect the bonding jumper from the valve.
 (4)  S 034-006Loosen the clamp on each end of the valve.
 (5)  S 034-007Move the duct sleeves away from the valve.
 (6)  S 024-050Remove the valve. (a) If you cannot remove the inboard exhaust valve through the floor beams, do the steps that follow: 1) Remove the walkway panel that is forward of the inboard exhaust valve and left of the center line. 2) Disconnect the antenna cables from the duct section that is forward of station 560. 3) Loosen the clamps from the duct section forward of station 560 (3 locations).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-58-04
 ALL  ú ú 05 Page 404 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 4) Move the duct sleeves away from the duct joints. 5) Remove the adjacent section of the bypass duct. 6) Remove the duct support clamp from the duct at station 560. 7) Turn the duct section until you can remove the inboard
 exhaust valve through the opening at station 560.
 S 034-008
 (7)  Put a cover on the duct openings.
 TASK 21-58-04-404-009
 3. Nine-Inch Valve Installation (Fig. 401)
____________________________
 A. References
 (1)  
24-22-00/201, Manual Control

 (2)  
25-52-01/401, Containerized Cargo Compartment Ceiling and Sidewall Linings

 (3)  
IPC 21-58-04 Fig. 2

 (4)  
IPC 21-58-04 Fig. 3

 (5)  
WDM 21-58-12, 21-58-13

 (6)  
SSM 21-58-03

 B. Access
 (1)  Location Zone 121 Forward Cargo Compartment Forward Half, LH
 C. Install the Valve
 S 434-010
 (1)  Remove the covers from the duct openings.
 (a)  Make sure there is no unwanted material in the ducts.
 S 424-011
 (2)  Put the valve in its position in the duct.
 (a)  
Make sure you can connect the electrical connector and the bonding jumper to the valve.

 (b)  
Make sure the flow arrow on the inboard exhaust valve points in the forward direction.

 NOTE: The flow arrow on the inboard exhaust valve points
____ in the opposite direction of the air flow to make sure you can get access to the manual override handle.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AIR CONDITIONING 2(92)