(b)  
191N-L for pack 2,

 (c)  
192H-R for pack 3.

 D.  Remove the Water Collector
 S 024-014
 WARNING: DO NOT TOUCH THE PACK DUCTS OR PACK COMPONENTS WHEN THEY ARE
_______ HOT. IF THE PACK WAS ON, THE DUCTS CAN BE SUFFICIENTLY HOT TO CAUSE INJURY TO PERSONS.
 (1)  Do these steps to remove the water collector from pack 1 or pack 2:
 (a)  
Disconnect the drain line at the forward end of the water collector.

 (b)  
Remove the three rods from the support clamp (see Fig. 401, View A-A).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-51-25
 ALL  ú ú 14 Page 401 ú Oct 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

PACK 2 WATER COLLECTOR
SEE A
FWD PACK 3 WATER COLLECTOR
SEE B PACK 1 WATER COLLECTOR
SEE A
HEAT EXCHANGER CLAMP (REF) SEALING
A ROD
ROD
A FWD
INBD 
FLOW CONTROL 
AND SHUTOFF 
VALVE (REF)  CLAMP  SUPPORT  WATER 
SEALING CLAMP  COLLECTOR 
WATER COLLECTOR  INBD  ROD 

(PACK 1 SHOWN, PACK 2 ALMOST THE SAME) A-A
A
Water Collector Installation Figure 401 (Sheet 1)
A79193
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-51-25
 ALL  ú ú 14 Page 402 ú Oct 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
HEAT EXCHANGER (REF)
CLAMP
SEALING

CLAMP SEALING
SEE D
TURBINE BYPASS VALVE (REF)
DUCT
CLAMP ASSEMBLY
SEALING
FLOW CONTROL
AND SHUTOFF

WATER  INBD
FWDVALVE (REF) COLLECTOR
SEE C
WATER COLLECTOR
B
BRACKET
SUPPORT CLAMP
DUCTWATER ASSEMBLY
COLLECTOR SUPPORT CLAMP
CLAMP
SEALING

BOLTS, WASHERS, NUTS, SPACERS
COLLECTOR
ROD
WATER

ROD
FWD
INBD
BRACKET
FWD
C D
Water Collector Installation
Figure 401 (Sheet 2)

A79230
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-51-25
 ALL  ú ú 14 Page 403 ú Oct 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (c)  
Remove the clamps and sealings from the ends of the water collector.

 (d)  
Remove the water collector.

 (e)  
Remove the support clamp from the water collector.

 S 024-005
 (2) Do these steps to remove the water collector from pack 3:
 (a)  
Disconnect the drain line from the outboard end of the water collector.

 (b)  
Remove the duct assembly connected to the outboard end of the water collector: 1) Remove the clamp and the sealing at the two ends of the

 duct assembly. 2) Disconnect the rods from the support clamp on the duct assembly (see Fig. 401, Detail C). 3) Remove the duct assembly.

 (c)  
Remove the clamp and the sealing at the inboard end of the water collector.

 (d)  
Disconnect the support clamp on the water collector: 1) Remove the fasteners that hold the support clamp to the brackets (see Fig. 401, Detail D).

 2)  Make a record of the location of the spacers to help when you install the water collector.

 (e)  
Remove the water collector.

 (f)  
Remove the support clamp installed on the water collector.

 TASK 21-51-25-404-006
 3.  Water Collector Installation (Fig. 401)____________________________
 A.  References
 (1)  21-00-00/201 Air Conditioning
 B.  Access
 (1)  
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調(diào) AIR CONDITIONING 2(53)