27-58-01
 ALL  ú ú 01 Page 407 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 B. Access
 (1)  
Location Zone
 581 Rear Spar to Trailing Edge, LH (LO Transmitter)
 572 Rear Spar to Trailing Edge, LH (LI Transmitter)
 672 Rear Spar to Trailing Edge, RH (RI Transmitter)
 681 Rear Spar to Trailing Edge, RH (RO Transmitter)

 (2)  
Access Panels
 581MB Flap Drive Access Panel (LO Transmitter)
 572FB Trailing Edge Lowerng Edge (LI Transmitter)
 672FB Trailing Edge Access Panel (RI Transmitter)
 681MB Flap Drive Access Panel (RO Transmitter)

 C.
Install the RVDT Transmitter

 S 284-009
 (1)  
Make sure the two indicator windows are in the zero (neutral rig) position.

 (a)  
Make sure the two lines in the fine adjustment indicator window are aligned (Fig. 401, views A-A and G or views E-E and K).

 (b)  
If the transmitter is not in the zero position, adjust the transmitter: 1) Push the locking tabs in against the RVDT housing. 2) Turn the input shaft until the line on the fine adjustment

 indicator window is in the center of the tolerance band.
 S 864-010
 CAUTION: EXTEND THE TE FLAPS HYDRAULICALLY TO THE 30-UNIT POSITION
_______ FOR THE RVDT TRANSMITTER REMOVAL AT THE FLAP TRANSMISSION. DO NOT EXTEND THE TE FLAPS BY THE ELECTRICAL MODE. IF YOU USE THE ELECTRICAL MODE, THE FLAPS WILL NOT GO TO THE CORRECT POSITION AND CAN CAUSE DAMAGE TO THE FLAPS WHEN YOU OPERATE THEM IN THE HYDRAULIC MODE.
 (2)  Do this task to extend the TE flaps to the 30-units position: "Trailing Edge Flap Extension with Hydraulic Power" (AMM 27-51-00/201).
 S 424-053
 CAUTION: MAKE SURE THAT YOU INSTALL THE RVDT TRANSMITTER CORRECTLY IN
_______ THE TRANSMISSION HOUSING. IF YOU DO NOT INSTALL IT CORRECTLY, THE TRANSMITTER INPUT SHAFT CAN BE DAMAGED.
 (3)  Install the RVDT transmitter in the flap transmission.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-58-01
 ALL  ú ú 01 Page 408 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 CAUTION:_______ DO NOT TOUCH THE LOCKING TABS OR THE SPLINED SHAFT DURING
 THE RVDT INSTALLATION.  THE LOCKING TABS WILL NOT LET THE
 INPUT SHAFT TURN DURING THE INSTALLATION.  DURING THE
 CLAMP-UP, THE LOCKING TABS WILL AUTOMATICALLY RELEASE THE
 INPUT SHAFT.  IF YOU BEND OR DAMAGE THE LOCKING TABS YOU
 CAN CAUSE DAMAGE TO THE RVDT AND YOU CAN CAUSE FLAP SYSTEM

 EICAS MESSAGES TO APPEAR.
 (a)  Engage the splined transmitter shaft with the drive pinion.
 CAUTION: PUSH THE RVDT IN COMPLETELY BEFORE YOU ALIGN THE BOLT HOLES OR
_______ CONNECTOR. IF YOU DO NOT PUSH THE RVDT IN COMPLETELY THE LOCKING TABS WILL NOT RELEASE THE SHAFT AND THE SHAFT CAN BE TWISTED/BENT.
 (b)  Push the transmitter in completely.
 NOTE: This will cause the locking tabs to release.
____
 (c)  
When you install the transmitter, make sure the electrical connectors are in these positions: 1) The electrical connector is in the down position for the

 two inboard transmitters. 2) The electrical connector is in the aft position for the left outboard transmitter. 3) The electrical connector is in the 45 degrees forward down position for the right outboard transmitter.

 (d)  
If it is necessary, you can turn the transmitter |10° to align the mounting holes.

 S 424-060
 CAUTION: PUSH THE RVDT IN COMPLETELY BEFORE YOU ALIGN THE BOLT HOLES OR
_______ CONNECTOR. IF YOU DO NOT PUSH THE RVDT IN COMPLETELY THE LOCKING TABS WILL NOT RELEASE THE SHAFT AND THE SHAFT CAN BE TWISTED/BENT.
 (4)  
Install two bolts and washers.

 (a)  
Tighten the bolts.

 (5)  
Install the electrical connector.

 S 714-061

 (6)  
Do this task: "Operational Test of the RVDT Transmitter at the Flap Transmission" (AMM 27-58-01/501).

 S 434-013
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 6(19)