(a)
Put the speed brake control lever in the FLIGHT position.

 (b)
Make sure the spoilers move to the 20-degree position.

 (c)  
Put the speed brake control lever in the UP position. 1) Make sure the spoilers move to the full up position (45 degrees).

 2)  Make sure the quadrant and the ratio changer linkage move freely.

 (d)  
Move the control lever to the DOWN position. 1) Make sure the spoiler moves to the full down position.

 (e)  
Make sure the quadrant and the ratio changer linkage move freely.

 E.  
Put the Airplane Back to Its Usual Condition

 S 862-030
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
 (1) Put the flap control lever in the UP detent to retract the flaps.
 S 092-021
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Do this task: "Removal of the Door Locks on the Wing Landing Gear" (Ref 32-00-30/201).

 S 862-022

 (3)  
Do this task to depressurize hydraulic system No. 4: "Hydraulic System Depressurization" (Ref 29-11-00/201).

 (4)  
Do this task: "Remove Electrical Power" (Ref 24-22-00/201).

 (5)  
Close the wing access panel.

 S 862-023
 S 412-024
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-06
 ALL  ú ú 01 Page 209 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 TASK 27-61-06-352-025
 4.  Inboard Flight Spoiler Quadrant Repairs_______________________________________
 A. Standard Tools and Equipment
 (1)  
Rivet - BACR15BB6D

 (2)  
Rivet - BACR15BB6B

 B.
Consumable Materials

 (1)
C00528 Compound - Corrosion Preventive, MIL-C-16173, Grade 2

 C.
Access

 (1)  
Location Zone
 575 Spoiler No. 5
 675 Spoiler No. 8

 (2)  
Access Panel
 572FB Access Panel - Trailing Edge Lower, LH
 672FB Access Panel - Trailing Edge Lower, RH

 D.
Procedure

 S 022-026
 (1)  
Do this task: "Inboard Flight Spoiler Quadrant Removal" (Ref Paragraph 2).

 S 352-027

 (2)  
Repair the quadrant:

 CAUTION:_______DO NOT MAKE THE RIVET HOLES LARGER. YOU WILL CAUSE DAMAGE TO THE EQUIPMENT.
 (a)  
Remove the broken parts of the rivets from the holes.

 (b)  
Install the new shear rivets. 1) Use a BACR15BB6D for the lever shearout. 2) Use a BACR15BB6B for the rig pin shearout.

 (c)  
Examine the marker for the shearout on the lever.

 NOTE: There is no marker for the rig pin shearout.
____
 1) Replace the marker if it is damaged or not there.
 (d)  Clean the inspection hole for lever shearout.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-06
 ALL  ú ú 01 Page 210 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (e)  Fill the inspection hole with the corrosion preventive compound.
 S 422-028
 (3)  Do this task: "Inboard Flight Spoiler Quadrant Installation" (Ref Paragraph 3).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(90)