(3)
4MIT65B80307-1 or A27021-30, Protractor

 (4)
G12001-50, Rig Pin Kit

 B.
Consumable Materials

 (1)  
A00344, Compound - Soft Filmed (corrosion preventive), MIL-C-11796, Class 2 or 3

 (2)
B00083, Solvent - TT-N-95, Aliphatic Naphtha

 (3)
A00704, Sealant - Silicone, RTV-162

 (4)
A00247, Sealant - Chromate, BMS 5-95

 C.
Parts

 ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 201 | 1 | Control Package | 27-61-04 | 02 | 50 | | | 3 | Bolt | | | 55 | | | 4 | Washer | | | 60 | | | 5 | Nut | | | 65 | | | 5A | Shim | | | 67 | | | 6 | Rod Assy (Control Rod) | | | 100 | | | 7 | Washer (RH Side) | | | 75 | | | | Washer (LH Side) | | | 80 | | | 8 | Bolt | | | 70 | | | 9 | Nut | | | 90 | | | 10 | Washer (RH Side) | | | 75 | | | | Washer (LH Side) | | | 80 | | | 11 | Washer | | | 15 | | | 12 | Antirotation Plate | | | 45 | | | 13 | Nut | | | 20 | | | 14 | Bolt | | | 25 | | | 15 | Bushing | | | 40 | | | 16 | Nut | | | 35 | | | 17 | Washer | | | 30 | | | 18 | Bolt | | | 10 | 2......…........…...................................…..........….....….........1
 D. References
 (1)
AMM 12-12-01/301, Hydraulic Systems

 (2)
AMM 24-22-00/201, Manual Control

 (3)
AMM 27-61-00/501, Spoiler Control System

 (4)
AMM 27-62-00/501, Speed Brake Control System

 (5)
AMM 29-11-00/201, Main Hydraulic Supply System

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-04
 ALL  ú ú 01 Page 206 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 E.  Access
 (1)  
Location Zone
 575 Spoiler No. 5
 675 Spoiler No. 8

 (2)  
Access Panel
 572FB Trailing Edge Lower
 672FB Trailing Edge Lower

 F.  
Install the Spoiler Control Package

 S 862-015
 (1)  
Make sure that hydraulic system No. 4 is depressurized

 S 222-017

 (2)  
Make sure the distance from the centerline of the rod end bearing to the checknut is 2.40 |0.05 inches(61 |1.27mm).

 S 422-018

 (3)  
Install the spoiler control package (Fig. 201):

 (a)  
Put the control package (1) in its position and install the four bolts (3), washers (4), and nuts (5).

 (b)  
Seal the bolts with the sealant.

 (c)  
Connect the hydraulic lines (2) to the control package (1): 1) Remove the caps from the hydraulic lines and the ports of

 the control package. 2) Connect the hydraulic lines to the control package.

 (d)  
Attach the input arm rod assembly (6) to the input arm: 1) Put the rod assembly in its position.

 NOTE: Make sure the rod end with the larger diameter,
____ points forward. Make sure you can get access to the lubrication fittings on the rod ends.
 2)  Install the bolt (8), washer (10), nut (9) and cotter pin on the rod.
 (e)  
If it is necessary, install the antirotation plate (12), with the bolt (18), washers (11), and nut (13).

 (f)  
Connect the piston rod end of the control package to the spoiler: 1) Install the bolt (14), bushings (15), washer (17) and nut

 (16).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-04
 ALL  ú ú 01 Page 207 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 2) Hold the bolt head with the spoiler socket adapter assembly. 3) Tighten the nut to 1500-1800 pound-inches(169.5-203.4Nm) more than the run-on torque. 4) Remove the spoiler socket adapter assembly.
 S 862-019
 (4)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(69)