曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

A
747-400 MAINTENANCE MANUAL
 D. Parts
 ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Inbd Panel Assy (Spoiler) | 27-61-01 | 02 | 150 | | | 2 | Seal Plate (Right) | | | 120 | | | | Seal Plate (Left) | | | 125 | | | 3 | Washer | | | 110 | | | 4 | Bolt | | | 105 | | | 5 | Bushing | | | 85 | | | 6 | Washer | | | 95 | | | 7 | Bolt | | | 70 | | | 8 | Bolt | | | 146 | | | 9 | Washer | | | 147 | | | 10 | Washer | | | 148 | | | 11 | Nut | | | 149 | | | 12 | Nut | | | 100 | | | 13 | Captive Bearing | | | 90 | | | 14 | Nut | | | 115 | | | 15 | Washer | | | 30 | | | 16 | Bolt | | | 15 | | | 17 | Washer | | | 25 | | | 18 | Nut | | | 40 | | | 19 | Washer | | | 35 | | | 20 | Bushing | | | 20 | | | 21 | Antirotation Plate (Antirotation | | | 65 | | | | Washer) | | | | | | 22 | Bolt | | | 10 | | | 23 | Nut | | | 60 | | | 24 | Washer | | | 55 | | | 25 | Spacer | | | 50 | | | 26 | Bolt | | | 45 | | | 27 | Antirotation Plate | 27-61-04 | 02 | 45 | | | 28 | Washer | | | 15 | | | 29 | Nut | | | 20 | | | 30 | Bolt | | | 25 | | | 31 | Bushing | | | 40 | | | 32 | Control Package | | | 50 | | | 33 | Nut | | | 35 | | | 34 | Washer | | | 30 | | | 35 | Bolt | | | 10 | 2......…........…...................................…..........….....….........1
 E. References
 (1)
AMM 12-21-21/301, Spoiler Control System

 (2)
AMM 24-22-00/201, Manual Control

 (3)
AMM 27-61-00/501, Spoiler Control System

 (4)
AMM 27-61-01/601, Inboard Flight Spoilers

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-01
 ALL  ú ú 01 Page 407 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (5)  
AMM 29-11-00/201, Main Hydraulic Supply System

 F.  
Access

 (1)  
Location Zone
 575 Spoiler No. 5
 675 Spoiler No. 8

 G.  
Procedure

 S 224-012
 (1)  
Do this task if you will install used hinge bolts or bushings: "Inboard Flight Spoiler Inspection" (AMM 27-61-01/601).

 S 424-013

 (2)  
Install the spoiler:

 (a)  
Apply a thin layer of grease to the control package mounting bolt, and the hinge bolts.

 (b)  
If it is necessary, install the seal plates (2) and the captive bearing (13).

 (c)  
Put the spoiler in its position.

 (d)  
Install the four hinge bolts (7, 16, and 22), washers (6, 15, and 17), and bushings (5 and 20).

 NOTE: Install the bolts with their heads outboard.
____
 1)  If it is necessary, install the antirotation washer (21) with a bolt (26), a spacer (25), a washer (24) and a nut (23).
 (e)  
Install a washer (19) and a nut (18) at hinges No. 2 and 3. 1) Tighten the nuts (18) to 2700-3300 pound-inches

 (305.1-372.8 Nm).
 2) Install the cotter pins.

 (f)  
Install the washers (6) and nuts (12) on the two hinges No. 1. 1) Tighten the nuts (12) to 100-200 pound-inches

 (11.3-22.6Nm). 2) Loosen the nut to align the nearest cotter pin hole. 3) Make sure the torque on the nut is not less than
 100 pound-inches (11.3Nm).
 4) Install the cotter pin.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-01
 ALL  ú ú 01 Page 408 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (g)  
Clean the mating surfaces for the bonding jumper.

 (h)  
Install the bonding jumpers at the outer hinges, with the bolts (8), washers (9 and 10), and nuts (11).

 NOTE: Install the bolts with their head on the inner side of
____
 the hinge bracket.

 (i)  
Use the milliohmmeter to make sure the resistance of the bonding jumper connection is less than 0.010 ohms.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(47)