(j)  
Manually turn the spoiler to do a check of the friction in the hinge.

 (k)  
If it is necessary, install the antirotation plate (27) with the bolt (35), washers (28), and nut (29).

 NOTE: Do not tighten the nut (29) until you install the
____
 bolt (30).

 (l)  Attach the control package (32) to the spoiler (1): 1) Install the bolt (30), bushings (31), washer (34) and nut (33). 2) Hold the bolt head with the spoiler socket adapter assembly. 3) Tighten the nut (33) to 1500-1800 pound-inches
 (169.5-203.4Nm) above the run-on torque. 4) Remove the spoiler socket adapter assembly. 5) If it is necessary, tighten the nut (29).
 S 644-014
 (3)  
Do this task to lubricate the spoiler hinges: "Spoiler Control System Lubrication" (AMM 12-21-21/301).

 (4)  
Remove the spoiler actuator locking tool.

 (5)  
Remove the sling assembly from the spoiler.

 S 094-015
 S 094-016
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-01
 ALL  ú ú 01 Page 409 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 H. Examine the Spoiler Clearances
 S 864-017
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  
Do this task to pressurize hydraulic systems No. 1 and 4:
 "Hydraulic System Pressurization" (AMM 29-11-00/201).

 S 864-018

 (2)  
Put the speed brake control lever in the DOWN position to lower all spoilers.

 S 224-019

 (3)  
Make sure the clearance between the spoiler and the outboard fixed wing structure is 0.55 to 0.91 inch (13.97 to 23.11mm).

 S 224-020

 (4)
Make sure the clearance between all adjacent spoilers is 0.95 to

 1.05 inches (24.13 to 26.67mm).
 S 824-021
 (5)  
If a clearance is not in the tolerance, adjust the spoiler:

 (a)  
Remove the bolt (16), washers (15, 17 and 19) and nut (18) at hinge No. 2.

 (b)  
Add or remove the washers (15) from the inboard side of the hinge to get the clearance in the tolerance.

 (c)  
Install the bolt, washers and nut. 1) Tighten the nut to 2700-3300 pound-inches (305.1-372.8Nm). 2) Install the cotter pin.

 I.
Do a Check of the Spoilers Seals

 S 214-022
 (1)  Make sure the seals between the spoiler and the fixed wing structure touch with a compression of 25-30 percent.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-01
 ALL  ú ú 01 Page 410 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 214-023
 (2)
Make sure the seals between the spoilers do not have an overlap.

 S 824-024

 (3)  
Adjust the seals if they are not in the correct position:

 (a)  
Loosen the screws that attach the seals.

 (b)  
Adjust the seals.

 (c)  
Tighten the screws.

 S 214-025
 (4)  
Make sure the seals on hinge No. 1 are not compressed more than 95 percent.

 J.
Examine the Spoiler to Flap Clearance (Fig. 402)

 S 864-026
 WARNING:_______OPEN THE CIRCUIT BREAKER TO PREVENT THE SPOILER RETRACTION. IF YOU USE THE SPEED BRAKE LEVER TO LIFT THE SPOILERS, AND IF YOU RELEASE PRESSURE IN SYSTEMS NO. 1 AND 4, THE SPOILERS WILL AUTOMATICALLY RETRACT. THIS CAN CAUSE INJURY TO PERSONS.
 (1)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P7, Overhead Circuit Breaker Panel
 1) 7G6, SPEED BRAKE AUTO CONT

 S 864-027
 (2)  
Do this task: "Supply Electrical Power" (AMM 24-22-00/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(48)