TASK 27-51-45-404-037
10. Outboard Flap Track Fairing Drive Rod Installation__________________________________________________
A. References
(1)
IPC 27-51-44 Fig. 1 (Tracks No. 1 and 8)
(2)
IPC 27-51-50 Fig. 1 (Tracks No. 2 and 7)
(3)
IPC 27-51-71 Fig. 1
B.
Access
(1)
Location Zone 567 Outboard Flap Track Fairing, Outboard Flap, LH, (Track No. 1) 565 Inboard Flap Track Fairing, Outboard Flap, LH, (Track No. 2) 665 Inboard Flap Track Fairing, Outboard Flap, RH, (Track No. 7)
667 Outboard Flap Track Fairing, Outboard Flap, RH, (Track No. 8)
C. Procedure
S 424-038
(1) Install the drive rod (Fig. 401):
NOTE: You will connect the drive rod to the midflap fitting during
____ the outboard flap track fairing adjustment.
(a) Attach the drive rod to the fixed drive link (Detail B): 1) Install the bushing in the fixed drive link. 2) Put the drive rod on the fixed drive link and install the
bolt, washers and nut.
3) Tighten the nut to 200-300 pound-inches (23-34 N-m). Continue to tighten the nut to align the subsequent cotter pin hole.
4) Install the cotter pin.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-45
ALL ú ú 03 Page 418 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 824-039
(2) Do this task: "Outboard Flap Track Fairing Adjustment" (Ref Paragraph 12).
TASK 27-51-45-404-040
11. Outboard Flap Track Fairing Attachment Fitting Installation___________________________________________________________
A. Consumable Materials
(1)
C00259 Primer - BMS 10-11, Type 1
(2)
A00359 Sealant - BMS 5-95, Type 1, Class B
B.
References
(1)
IPC 27-51-44 Fig. 1 (Tracks No. 1 and 8)
(2)
IPC 27-51-50 Fig. 1 (Tracks No. 2 and 7)
C.
Access
(1)
Location Zone 567 Outboard Flap Track Fairing, Outboard Flap, LH, (Track No. 1) 565 Inboard Flap Track Fairing, Outboard Flap, LH, (Track No. 2) 665 Inboard Flap Track Fairing, Outboard Flap, RH, (Track No. 7)
667 Outboard Flap Track Fairing, Outboard Flap, RH, (Track No. 8)
D. Procedure
S 164-041
(1)
Clean the paint from the bolt holes on the attachment fitting and from the used bolts.
S 424-042
(2)
Install the attachment fitting (Fig. 401):
(a)
Install the attachment fitting on the flap track (Section D-D):
CAUTION: MAKE SURE THE CLEARANCE BETWEEN THE ATTACHMENT
_______ FITTING AND THE FLAP TRACK IS NOT MORE THAN 0.003 INCH AFTER YOU INSTALL THE SHIMS. YOU CAN CAUSE DAMAGE TO THE ATTACHMENT FITTING.
1) If it is necessary, remove 0.003 inch (0.076 mm) laminations from the shims to make sure the clearance between the attachment fitting and the flap track is not more than 0.003 inch (0.076 mm).
2) Install the shims with the wet primer. 3) Put the attachment fitting on the flap track and install the bolts with the wet primer.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-45
ALL ú ú 02 Page 419 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
4) On airplanes with lockwire bolts, put the attachment fitting on the flap track and install lockwire bolts with wet sealant.
5) Tighten the two top bolts and the forward bolt on each side of the flap track to 125-155 pound-inches (14-18 N-m).
6) Tighten the five lower bolts and the two aft bolts on each side of the flap track to 170-210 pound-inches (19-24 N-m).
(b) Attach the fixed drive link to the attachment fitting (Section C-C): 1) Install the bushings in the attachment fitting. 2) Put the pin through the fixed drive link and the attachment
fitting. 3) Install the bolt, washers and nut to attach the pin to the attachment fitting. 4) Tighten the nut to 60-85 pound-inches (7-10 N-m).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(2)
