0.006
(0.152)
0.007
11
(0.178)
12
0.006
(0.152)
0.007
13
(0.178)
REPLACE WHEN THE RADIAL CLEARANCE BETWEEN THE RACES IS MORE THAN 0.005 INCH (0.127 mm).
HARD CHROME PLATE TO THE MAXIMUM THICKNESS OF 0.005 INCH (0.127 mm) PER QQ-C-320 AND GRIND TO THE DESIGN LIMIT.
THE REPLACEMENT BUSHING CAN HAVE OVERSIZE OD TO +0.03 INCH (+0.762 mm).
REPLACE WHEN THE RADIAL CLEARANCE BETWEEN THE RACES IS MORE THAN 0.006 INCH (0.1524 mm).
Outboard Flight Spoiler Wear Limits
Figure 601 (Sheet 4)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-02
ALL ú
ú 01 Page 606
ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
SPOILER DIFFERENTIAL MECHANISM - MAINTENANCE PRACTICES
______________________________________________________
1. General_______
A. There are five tasks in this procedure. There is a task for the removal, the installation, a functional test, an inspection, and a repair of a spoiler differential mechanism.
(1)
The removal procedure has these parts:
(a)
The installation of the wing landing gear door lock
(b)
The depressurization of the hydraulic systems
(c)
The removal of the differential mechanism.
(2)
The installation of the spoiler differential mechanism has these parts:
(a)
A check of the parts that attach the differential mechanism for worn areas
(b)
The installation of the differential mechanism
(c)
A lubrication of the differential mechanism
(d)
The functional test of the differential mechanism
(e)
The removal of the wing landing gear door locks.
(3)
The functional test of the spoiler differential mechanism has these parts:
(a)
The application of electrical and hydraulic power
(b)
The operation of the spoilers with the control wheel
(c)
A check that the spoilers are aligned
(d)
The operation of the spoilers with the speed brake control lever
(e)
The removal of the electrical and hydraulic power.
(4)
To do the inspection of the spoiler differential mechanism you measure the inner and outer diameters of the input cranks, the levers, and the bolts. You must remove the spoiler differential mechanism to do the inspection. The inspection is usually done before you install a differential mechanism.
(5)
The repair of the spoiler differential mechanism includes the replacement of the shear rivets in the lever.
TASK 27-61-03-002-001
2. Spoiler Differential Mechanism Removal (Fig.______________________________________201)
A. References
(1)
32-00-30/201, Landing Gear Door Locks
(2)
IPC 27-61-03 Fig. 2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-03
ALL ú ú 01 Page 201 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
B. Access
(1)
Location Zone
135 Wing Landing Gear Wheel Well, LH
136 Wing Landing Gear Wheel Well, RH
C.
Procedure
S 492-002
(1) Make sure the ground lockpins for the landing gear are installed.
S 492-003
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(61)
