if you lifted them.
(b)
Do this task: "Hydraulic System Depressurization"
(AMM 29-11-00/201).
CAUTION: LOOSEN THE CHECKNUT SUFFICIENTLY TO MOVE THE TAB ON THE
_______ LOCKING DEVICE OUT OF THE SLOT IN THE PISTON ROD. YOU CAN BREAK THE TAB FROM THE LOCKING DEVICE.
(c) Loosen the checknut on the piston rod end.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-02
ALL ú ú 01 Page 413 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
CAUTION: DO NOT TURN THE PISTON ROD IF THE CONTROL PACKAGE IS
_______
PRESSURIZED. YOU CAN CAUSE DAMAGE TO THE INTERNAL SEALS.
(d) Turn the piston rod to adjust the clearance between the spoiler
and the flap.
NOTE: Each 1/4 turn of the piston rod will change the____
clearance by approximately 0.14 inch.(3.556mm) If you
turn the piston rod to change the clearance by 0.35 inch
(8.89mm)or more, you must do the spoiler system
adjustment (AMM 27-61-00/501).
(e) Fill the rod end with the corrosion preventive compound before
the adjustment if it is necessary:
NOTE: If the piston rod is not full of the corrosion____
preventive compound, there will be corrosion.
1) Fill the rod end if you removed it from the control
package.
2) Fill the rod end if you moved the rod end out of the piston
0.50 inch (12.7mm) or more.
3) Remove the rod end from the spoiler and the control
package.
(f) Fill the piston with the corrosion preventive compound.
(g) Install the rod end.
(h) Engage the locking device with the piston rod.
(i) Apply a layer of the corrosion preventive compound on the
external threads.
(j) Tighten the checknut hand tight.
S 864-048
(12)
Do this task: "Hydraulic System Pressurization" (AMM 29-11-00/201).
S 864-049
(13)
Put the speed brake control lever in the DOWN position to lower all spoilers until the control package piston is fully retracted.
(a)
Make sure the clearance between the spoilers and the flaps are in the tolerance shown in Fig. 402. There is no specified maximum clearance. 1) If the clearance is not in the tolerance, loosen the
checknut and adjust the spoiler again.
(b)
If the clearance is in the tolerance, tighten the checknut to 1200-1300 pound-inches(135.6-146.9Nm) (for spoilers No. 1, 2, 3, 4, 9, 10, 11 and 12).
(c)
Loosen the checknut and make sure the parts of the locking device stay engaged correctly.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-02
ALL ú ú 01 Page 414 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(d)
Tighten the checknut to 1200-1300 pound-inches(135.6-146.9Nm) (for spoilers No. 1, 2, 3, 4, 9, 10, 11 and 12). 1) Make sure the parts of the locking device stay engaged
correctly.
(e)
Install the lockwire on the checknut and the locking device.
(f)
Clean all grease from the checknut and the locking device with naphtha.
(g)
Apply the silicone sealant on the checknut and the locking device.
S 864-057
(14)
Lower the spoilers.
S 864-058
(15)
Do this task: "Hydraulic System Depressurization" (AMM 29-11-00/201).
S 094-059
(16)
Remove the safety device.
S 864-060
(17)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P7, Overhead Circuit Breaker Panel
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(58)
