曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

implies that the approach may not be flown at all
using Baro-VNAV when the temperature is below
-20° Celsius. However, Baro-VNAV may be used
for approach guidance down to the published
LNAV MDA. This information can be seen in the
notes section of the previous example.
In the example for the RNAV (GPS) RWY 30
approach, the note “DME/DME RNP-0.3 NA” prohibits aircraft that use only DME/DME sensors for
RNAV from conducting the approach.
Because these procedures can be flown with an
approach approved RNP system and “RNP” is not sensor specific, it was necessary to add this note to make it
clear that those aircraft deriving RNP 0.3 using
DME/DME only are not authorized to conduct the procedure.
The lowest performing sensor authorized for RNP navigation is DME/DME. The necessary DME NAVAID
ground infrastructure may or may not be available at
the airport of intended landing. The procedure designer
has a computer program for determining the usability
of DME based on geometry and coverage. Where FAA
Flight Inspection successfully determines that the coverage and accuracy of DME facilities support RNP, and
that the DME signal meets inspection tolerances,
although there are none currently published, the note
“DME/DME RNP 0.3 Authorized” would be charted.
Where DME facility availability is a factor, the note
would read, “DME/DME RNP 0.3 Authorized; ABC
and XYZ required,” meaning that ABC and XYZ DME
facilities are required to assure RNP 0.3.
AIRPORT/RUNWAY INFORMATION
Another important piece of a thorough approach
briefing is the discussion of the airport and runway
environment. A detailed examination of the runway
length (this must include the Airport/Facility
Directory for the landing distance available), the
intended turnoff taxiway, and the route of taxi to the
parking area, are all important briefing items. In
addition, runway conditions should be discussed.
The effect on the aircraft’s performance must be
considered if the runway is wet or contaminated.
NACO approach charts include a runway sketch on each
approach chart to make important airport information
easily accessible to pilots. In addition, at airports that
have complex runway/taxiway configurations, a separate full-page airport diagram will be published.
The airport diagram also includes the latitude/longitude
information required for initial programming of FMS
equipment. The included latitude/longitude grid shows
the specific location of each parking area on the airport
surface for use in initializing FMSs. Figure 5-19 shows
the airport sketch and diagram for Chicago-O’Hare
International Airport.
Pilots making approaches to airports that have this type
of complex runway and taxiway configuration must
ensure that they are familiar with the airport diagram
prior to initiating an instrument approach. A combination of poor weather, high traffic volume, and high
ground controller workload makes the pilot’s job on the
ground every bit as critical as the one just performed in
the air.
INSTRUMENT APPROACH PROCEDURE
BRIEFING
A thorough instrument approach briefing greatly
increases the likelihood of a successful instrument
approach. Most Part 121, 125, and 135 operators designate specific items to be included in an IAP briefing, as
well as the order in which those items will be briefed.
Before an IAP briefing can begin, flight crews must
decide which procedure is most likely to be flown from
the information that is available to them. Most often,
when the flight is being conducted into an airport that
has ATIS information, the ATIS will provide the pilots
with the approaches that are in use. If more than one
approach is in use, the flight crew may have to make an
educated guess as to which approach will be issued to
them based on the weather, direction of their arrival
into the area, any published airport NOTAMs, and previous experience at the specific airport. If the crew is in
contact with the approach control facility, they can
query ATC as to which approach is to be expected from
the controller. Pilots may request specific approaches
to meet the individual needs of their equipment or
regulatory restrictions at any time and ATC will, in
most cases, be able to accommodate those requests,
providing that workload and traffic permit.
If the flight is operating into an airport without a control tower, the flight crew will occasionally be given the
choice of any available instrument approach at the field.
In these cases, the flight crew must choose an appropriate approach based on the expected weather, aircraft
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Procedures Handbook (IPH)儀表程序手冊上(120)