曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

and departure phases of flight are critical portions of the
flight since the majority of this time is spent on the ground
with multiple actions occurring. It is the desire of the FAA
and the aviation industry to reduce runway surface events
of all types, but it cannot be done simply through policy
changes and educational programs. Pilots must take
responsibility for ensuring safety during surface operations and continue to educate themselves through
government (www.faa.gov/runwaysafety) and industry runway safety programs.
TAKEOFF MINIMUMS
While mechanical failure is potentially hazardous during any phase of flight, a failure during takeoff under
instrument conditions is extremely critical. In the event
of an emergency, a decision must be made to either
return to the departure airport or fly directly to a takeoff
alternate. If the departure weather were below the landing minimums for the departure airport, the flight would
be unable to return for landing, leaving few options and
little time to reach a takeoff alternate.
In the early years of air transportation, landing minimums for commercial operators were usually lower
than takeoff minimums. Therefore, it was possible
that minimums allowed pilots to land at an airport but
not depart from that airport. Additionally, all takeoff
minimums once included ceiling as well as visibility
Figure 2-7. National Blueprint for Runway Safety.
departure may be made, but it is never advisable. If commercial pilots who fly passengers on a daily basis must
comply with takeoff minimums, then good judgment and
common sense would tell all instrument pilots to follow the
established minimums as well.
NACO charts list takeoff minimums only for the runways at
airports that have other than standard minimums. These takeoff minimums are listed by airport in alphabetical order in
the front of the TPP booklet. If an airport has non-standard
takeoff minimums, a (referred to by some as either the
“triangle T” or “trouble T”) will be placed in the notes sections of the instrument procedure chart. In the front of the
TPP booklet, takeoff minimums are listed before the obstacle departure procedure. Some departure procedures allow a
departure with standard minimums provided specific aircraft
performance requirements are met. [Figure 2-8]
2-7
requirements. Today, takeoff minimums are typically
lower than published landing minimums and ceiling
requirements are only included if it is necessary to
see and avoid obstacles in the departure area.
The FAA establishes takeoff minimums for every airport
that has published Standard Instrument Approaches. These
minimums are used by commercially operated aircraft,
namely Part 121 and 135 operators. At airports where minimums are not established, these same carriers are required
to use FAA designated standard minimums (1 statute mile
[SM] visibility for single- and twin-engine aircraft, and 1/2
SM for helicopters and aircraft with more than two
engines).
Aircraft operating under Part 91 are not required to comply
with established takeoff minimums. Legally, a zero/zero
Figure 2-8. Takeoff minimums are listed in the front of each NACO U.S. Terminal Procedures booklet.
2-8
TAKEOFF MINIMUMS FOR
COMMERCIAL OPERATORS
While Part 121 and 135 operators are the primary users of
takeoff minimums, they may be able to use alternative
takeoff minimums based on their individual OpsSpecs.
Through these OpsSpecs, operators are authorized to
depart with lower-than-standard minimums provided they
have the necessary equipment and crew training.
OPERATIONS SPECIFICATIONS
Operations specifications (OpsSpecs) are required by
Part 119.5 to be issued to commercial operators to define
the appropriate authorizations, limitations, and procedures
based on their type of operation, equipment, and qualifications. The OpsSpecs can be adjusted to accommodate the
many variables in the air transportation industry, including
aircraft and aircraft equipment, operator capabilities, and
changes in aviation technology. The OpsSpecs are an
extension of the CFR; therefore, they are legal, binding
contracts between a properly certificated air transportation
organization and the FAA for compliance with the CFR's
applicable to their operation. OpsSpecs are designed to
provide specific operational limitations and procedures tailored to a specific operator's class and size of aircraft and
types of operation, thereby meeting individual operator
needs.
Part 121 and 135 operators have the ability, through the
use of approved OpsSpecs, to use lower-than-standard
takeoff minimums. Depending on the equipment installed
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Procedures Handbook (IPH)儀表程序手冊上(44)