曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

behalf to achieve this. Generally we only
recommend networked solutions and thus we can be of little assistance in software set-up in environments
that we don’t fully support. This applies to all PM programs. You can not run MSFS on one screen and a PM
program on another. Generally, this won’t work because only one program can be the “active” program at
one time and thus graphics acceleration is limited to the active program.
Project Magenta Revision: 12 March-08
8
Step 2. Installation of WideFS and FSUIPC
To connect MSFS and Project Magenta programs together, across a computer network, you need an
intermediary program called WideFS. Full docs are enclosed with these programs and are the most up-todate
and thorough source of information. Below is really just a quick start summary.
A registered version of FSUIPC must be installed in your MSFS Modules folder.
A registered version of WideFS is also required for network communications and the installation is as
follows.
WideFS is split into two main components as illustrated above.
The Wideserver component (Wideserver.dll and Wideserver.ini) are placed in your MSFS Modules folder.
That is all you need to do for the Sever component installation.
The Wideclient component (Wideclient.exe and Wideclient.ini) are placed on your client computers
(computer that you wish to connect to MSFS). You can create a folder perhaps called “WideClient” or copy
them into the PM main program folders – it actually does not matter. Each time you want communication
across the network with MSFS, Wideclient.exe must be running.
Step 3 Setting Server Name or Static IP
WideFS can use either the IPX network protocol for communication or TCP/IP. TCP/IP is now the standard
and we recommend its use on most systems. For IPX usage, please refer to Peter Dowson’s documentation
included with the WideFS package. There is also a new protocol in use called UDP. This is a faster protocol
but there is no error checking. It is purely system dependent as to whether this can be used. As a general
rule, most computer systems will run well using TCP/IP.
Generally, after installation (as above) of the various files included in WideFS, as a basic rule you should
not actually have to do anything more but we also like to at least edit the wideserver.ini file, use a text
editor like Windows Notepad. Add the following entries in the first Section of the Wideserver.ini file:
ServerName= (your Server’s Name)
Or
ServerIPAddr= (your Server’s IP address)
You only need to set either the ServerIPAddr or ServerName (not both). It is recommended that you use
the ServerName option. Then add to the same ini file ProtocolPreferred=TCP (or whatever protocol you
prefer) we recommend TCP at least to start with.
Project Magenta Revision: 12 March-08
9
If you do not know how to find your ServerName or IP address, please contact Project Magenta support or
refer to the WideFS documentation.
When you first try to “connect” wideclient to MSFS
you may need to allow access for this program by
any Firewalls you have enabled. Otherwise they
may block communication.
To check you have correctly set WideClient to
communicate with MSFS, run MSFS on the Server,
then start WideClient on your client PC by clicking
on wideclient.exe. In the menu bar at the top of
the Wideclient program you should see the
number of clients that are connected. If it is
indicating that nothing is connected, then you need to refer to the network checklist to make sure you have
set everything correctly.
Step 4 Additional things to do – Sharing
A) Share your default MSFS folder and give it full read/write access.
Right click on your MSFS main program folder, select properties, and
then look for the sharing options (typically on a sharing tab in winXP).
Select the option to share the folder and give it a share name with full
read/write access.
B) For FS9 / FSX, you need to share where the Flight Simulator Files
are stored. Go to your MyDocuments folder and find the sub folder
“Flight Simulator Files”. Right click on this folder and enable full
sharing as outlined above. The share name of this folder must be set
to FSPLANS. Write in FSPLANS where it indicates the share name.
When using WinXP, make sure the option for it to be a Private Folder
is not selected.
Step 5 NetDir
The NetDir setting is required if you own a copy of the PM CDU or MCDU program.
There are various ways to set the NetDir, it is important to ensure it has been set correctly for correct
operations between the CDU / MCDU and the Glass Cockpit.
a) Go to the program folder of the CDU or MCDU where you installed this software.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料13(2)