On the MCDU 2 scratchpad:
-
the VOICE "GO AHEAD" message comes into view.
At the bottom of the Engine/Warning Display (EWD):
-
the ACARS CALL message comes into view.
R 1EFF : 001-049, 101-105, 1 23-24-00Page 505 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R 24. On the MCDU 2 keyboard:
R - push the MCDU mode key.
R 25. On the MCDU 2:
R - push the line key adjacent to
R the ACARS indication.
R 26. On the MCDU 2:
R - push the line key adjacent to
R the indication related to the
R message received.
R 27. On the MCDU 2:
R - read the last message received
R and compare it with the ground
R message.
R 28. On the MCDU 2 keyboard:
R - push the MCDU MENU mode key.
R 29. On the ECAM control panel:
R - push the CLR key until the
R MEMO section comes into view
R on the lower ECAM DU.
R 30. On the RMP 2:
R - push the transfer pushbutton
R switch (double arrow) between
R the two windows.
R
R
R
R
R
R
On the MCDU 2:
-
the MCDU MENU page comes into view.
On the MCDU 2:
-
the ACARS MENU page comes into view.
On the MCDU 2:
-
the page that includes all the received messages comes into view.
On the MCDU 2:
-the MCDU MENU page comes into view.
After not many seconds, on the RMP 2 (and RMP 3 if installed):
-
the ACARS indication shows in the STBY display windows and the frequency (which was in the STBY display window of the RMP 2) shows in the ACTIVE display window.
At the bottom of the Engine/Warning Display (in the MEMO section):
-
the VOICE message comes into view.
R NOTE : If no ground station is available, you must do a reset of the ACARS
____ R MU (pushbutton switch on the front face of the ACARS MU). This will R prevent the queueing-up of the downlinks not sent.
R 1EFF : 001-049, 101-105, 1 23-24-00Page 506 1 1 May 01/05 1 1 1CES 1R **ON A/C 051-099,
R Subtask 23-24-00-710-050-A
R A. Operational Test of the ACARS
R -------------------------------------------------------------------------------R ACTION RESULT R -------------------------------------------------------------------------------
R 1. On the RMP 1, RMP 2 (and RMP 3 if
R installed):
R - set the ON/OFF selector switch
R to ON.
R 2. On the RMPs:
R - push the VHF 3 pushbutton
R switch.
R Two configurations are possible:
R First configuration:
R - the ACARS MU controls the VHF 3
R frequency.
R
R Second configuration:
R - the RMPs control the VHF 3
R frequency.
R
R
R 3. In the first configuration, go to
R step (5).
R In the second configuration, go
R to step (4).
R 4. On the RMP2 push, the transfer
R pushbutton switch (double arrow)
R between the two windows.
R
R
R
R 5. On the ACP 2:
Each RMP shows the last frequencies and the last function used.
On the RMPs:
-
the ACARS indication shows in the ACTIVE display window and a frequency shows in the STBY display window.
On each the RMPs:
-
the same frequency shows in the ACTIVE display window and the ACARS indication shows in the STBY display window.
On the RMPs: after not many seconds, the frequency (which was in the STBY display window of the RMP 1) shows in the ACTIVE display window and the ACARS indication shows in the STBY display window.
On the ACP 2:
R 1EFF : 051-099, 1 23-24-00Page 507 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R - push and release the VHF 3
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊1(106)
