曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R R  (12) Apply the SEALANTS (Material No. 09-016) to all the screw heads (2). 
R  (13) Apply the SEALANTS (Material No. 09-016) around the antenna base (1). 
R R  (14) Apply the STRUCTURE PAINTS (Material No. 16-021) to all of the sealed screw heads (2), and the antenna base seal.
 Subtask 23-12-11-865-055
R  C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2RC3.
 Subtask 23-12-11-710-051
 D. Do the operational test of the VHF system (Ref. TASK 23-12-00-710-001).
 5. Close-up________
 Subtask 23-12-11-942-051
 A. Put the aircraft back to its initial configuration.
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Remove the access platform(s).

 

_________________________________________________________
 TASK 23-12-33-000-001
 Removal of the VHF Transceiver (1RC1, 1RC2, 1RC3)
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific blanking caps
 No specific circuit breaker(s) safety clip(s)
 No specific access platform 1.6 m (5 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
23-12-33-991-001 Fig. 401
 3. Job Set-up
__________
 Subtask 23-12-33-865-050

 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 1RC1
 49VU COM/VHF/1 2RC1 G09 FOR 1RC2
 121VU COM NAV/VHF/2 2RC2 L04 R FOR 1RC3 R 121VU COM NAV/VHF/3 2RC3 L05
 1EFF : ALL 1 23-12-33Page 401 1 1 Feb 01/99 1 1 1CES 1 Subtask 23-12-33-010-050

 B. Get Access
 (1)
 Put the access platform in position at the access door 824 in zone

 128.

 (2)
 Open the access door 824.

 4. Procedure
_________
 (Ref. Fig. 401/TASK 23-12-33-991-001) Subtask 23-12-33-020-050
 A. Removal of the VHF Transceiver
 (1)
 Loosen the nuts (3).

 (2)
 Lower the nuts (3).

 (3)
 Pull the VHF transceiver (5) on its rack (2), to disconnect the electrical connectors (1).

 (4)
 Remove the VHF transceiver (5).

 (5)
 Put blanking caps on the disconnected electrical connectors (1).

 1EFF : ALL 1 23-12-33Page 402 1 1 Feb 01/98 1 1 1CES 1

 VHF Transceiver
 Figure 401/TASK 23-12-33-991-001
 1EFF :  ALL  1  23-12-33 Page 403 
1  1  Feb 01/98
 1  1
 1CES  1

 

 TASK 23-12-33-400-001
 Installation of the VHF Transceiver (1RC1, 1RC2, 1RC3)

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.6 m (5 ft. 3 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-12-00-710-001 Operational Test of the VHF System 23-12-00-740-001 BITE Test of the VHF System R 52-41-00-410-002 Close the Avionics Compartment Doors after Access 23-12-33-991-001 Fig. 401
 3. Job Set-up
__________
 Subtask 23-12-33-860-050

 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the access platform is in position at the access door 824 in zone 128.

 (2)
 Make sure that the access door 824 is open.

 1EFF : ALL 1 23-12-33Page 404 1 1 Feb 01/02 1 1 1CES 1 Subtask 23-12-33-865-051
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊1(81)