-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU, on the COM menu On the MCDU:
page:
-Push the line key adjacent to - the RMP 1(2,3) page comes into view. the RMP1(RMP2-RMP3) indication.
2. On the RMP 1(2,3) page:
-Push the line key adjacent to - the TEST OK indication comes into the TEST indication. view.
3. On the MCDU :
-On the MCDU, push the line key
adjacent to the RETURN
indication until the CFDS menu
page comes into view.
1EFF : ALL 1 23-13-00Page 511 1 1 May 01/05 1 1 1CES 1
R **ON A/C 106-149, 218-299, 301-399, 401-499,
Subtask 23-13-00-740-050-A
A. Bite Test of the Radio Management
NOTE : This test is for the system 1. For the other system(s), use the
____
indications between the parentheses.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU, on the COM menu On the MCDU:
page:
-Push the line key adjacent to - the RMP 1(2,3) page comes into view. the RMP1(RMP2-RMP3) indication.
2. On the RMP 1(2,3) page:
-Push the line key adjacent to - the initial conditions and the normal
the TEST indication. test sequence come into view the WAIT FOR 40 SECONDS indication comes into view the TEST OK indication comes into view.
3. On the RMP 1 page:
-the SWITCH ON RMP3 indication
is shown.
4. On the MCDU, push the line key
adjacent to the RETURN indication
until the CFDS menu page comes
into view.
R 1EFF : 106-149, 218-299, 301-399, 401-499, 1 23-13-00Page 512 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
5. Close-up
________ Subtask 23-13-00-862-052
A. Put the aircraft back to its initial configuration.
(1)
On the MCDU, set the BRT knob to OFF.
(2)
On the RMPs, set the ON/OFF selector switch to OFF.
(3)
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
1EFF : ALL 1 23-13-00Page 513 1 1 May 01/05R 1 1 1CES 1
RADIO MANAGEMENT PANEL (RMP) (1RG1,1RG2,1RG3) - REMOVAL/INSTALLATION
____________________________________________________________________
TASK 23-13-13-000-001
Removal of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
23-13-13-991-001 Fig. 401
3. Job Set-up
__________
Subtask 23-13-13-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 1RG1
49VU COM/RMP/1 2RG1 G10 FOR 1RG2 121VU COM NAV/RMP/2 2RG2 L02 FOR 1RG3 R 121VU COM NAV/RMP/3 2RG3 L03
1EFF : ALL 1 23-13-13Page 401 1 1 Nov 01/02 1 1 1CES 1R
4. Procedure
_________
(Ref. Fig. 401/TASK 23-13-13-991-001)
Subtask 23-13-13-020-050
A. Removal of the RMP
(1)
Loosen the quarter-turn fasteners (1).
(2)
Pull the RMP (2) from its housing.
(3)
Disconnect the plug (4) from the receptacle (3).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊1(93)
