(2)
Connect a 600 ohms Headset to the HEADSET connector of the Captain station.
1EFF : ALL 1 23-13-00Page 504 1 1 Nov 01/02R 1 1 1CES 1
Subtask 23-13-00-865-051
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
R **ON A/C 001-004, 051-060,
49VU NAV/ILS/1 1RT1 G12 **ON A/C ALL
49VU NAV/VOR/1 2RS1 G13 49VU COM/RMP/1 2RG1 G10 49VU COM/AUDIO/ACP/CAPT 4RN G06 49VU NAV/ADF/1 1RP1 H14
R **ON A/C 001-004, 051-060,
121VU COM NAV/ILS/2 1RT2 K09 **ON A/C ALL
121VU COM NAV/VOR/2 2RS2 K08 121VU COM NAV/ADF/2 1RP2 K02 121VU COM NAV/RMP/2 2RG2 L02
4. Procedure
_________
Subtask 23-13-00-710-051
A. Operational Test of the Radio Navigation Selection in Standby Mode with the RMP1 and 2
NOTE : This test is for the system 1. For the other system(s), use the
____
indications between the parentheses.
1EFF : ALL 1 23-13-00Page 505 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
1. On the RMP1 and RMP2:
-Set the ON/OFF selector switch to ON.
-
Push the NAV pushbutton switch.
-
Push the ILS pushbutton switch.
NOTE : For the RMPs that have the
____ LS label (and not the ILS label), push the LS pushbutton switch.
2. On the RMP1 (RMP2):
-In the STBY/CRS window set an ILS frequency of 109.5 Mhz with the dual selector knob.
-Start this frequency. To do this, push the transfer pushbutton switch (double arrow) between the two display windows.
-Set a course of C090 with the dual selector knob.
-Start this course. To do this, push the transfer pushbutton switch (double arrow) between the two windows.
-
The RMP shows the last frequenciesand the last function used.
-
The green LED on this pushbutton switch comes on.
-
The green LED on this pushbutton switch comes on.
-
The set ILS frequency comes into view on the RMP1 and RMP2 two display windows.
On the RMP1 and RMP2:
-
In the ACTIVE display window, the setfrequency comes into view.
On the RMP1 (RMP2):
-
In the STBY/CRS display window, the set course comes into view.
-
In the STBY/CRS display window, thecourse C090 comes into view.
-
In the STBY/CRS display window, thefrequency 109.5MHz comes into view.
1EFF : ALL 1 23-13-00Page 506 1 1 Nov 01/02R 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
3. On the RMP2 (RMP1):
-Push the NAV pushbutton switch.
-Set the ON/OFF selector switch to OFF.
4. On the RMP1 (RMP2):
-Push the VOR pushbutton switch.
-In the STBY/CRS display window, set a VOR frequency of 117.5 MHz with the dual selector knob.
-Start this frequency. To do this, push the transfer pushbutton switch (double arrow) between the two windows.
-Set a course of CO75 with the dual selector knob.
-Start this course. To do this, push the transfer pushbutton switch (double arrow) between the two windows.
5. On the RMP1:
-Push the ADF pushbutton switch.
-
The green LED on this pushbutton switch goes off.
-
The two display windows go off.
