R  SATCOM CONFIG Page 
R  Figure 014
 1EFF :  401-499,  1  23-28-00 Page 21 
1  1  Aug 01/05
 1  1
 1CES  1

R  (e) Part Numbers for SDU Owner Requirement Table are displayed 
R  adjacent to and below line key 3L. If the Protection Level 
R  applied to any of the four data-loadable Owner Requirement Table 
R  records is set to Protected/Modifiable and data in any 
R  Protected/Modifiable table has been modified, the word MOD is 
R  displayed adjacent to the 12-digit Part Number. The second Part 
R  Number is a 15 alphanumeric digit free text field. Both Part 
R  Number fields are user-definable and may be defined when 
R  generating the dataloadable ORT disk. 
R  (f) Aircraft ID is displayed adjacent to line key 4L. A PIN 
R  indication following the aircraft ID indicates it is decoded from 
R  the configuration pins. A XTALK indication shows the data is 
R  extracted from the crosstalk bus. 
R  A BUS indication shows the data is extracted from the 429 ACID 
R  bus. If the ACID bus is selected as the source and data has not 
R  been received, then dashes are displayed. 
R  (g) The Protected Level Code and the entry boxes are only available 
R  during In-Flight mode and only when the SDU is not Logged On. 
R  (5) SATCOM LOG page 
R  (Ref. Fig. 015) 
R  The SATCOM LOG page provides display of AES log-on and control of 
R  log-on. 
R  Owner preference and owner requirement tables are accessed via the 
R  SATCOM- MAINT menu display. This page may be entered from the MAIN 
R  MENU page or from any other page when the active advisory "LOG-ON >" 
R  is displayed. 
R  This page provides selection and control of the log-on process. 
R  Sat ID and GES ID and the Log-On select can be entered when in user 
R  commanded (manual) log-on mode and in the WAIT USER INPUT state. The 
R  log-on status is displayed adjacent to line key 1L. The following 
R  status messages are displayed, under the conditions described. 
R  WARMING: 
R  This status is shown under any of the following conditions: 
R  - the SDU is initializing data following a power cycle, 
R  - or the HSR status of the RFU is in the warm-up state, 
R  - or the BSU is reporting self-test. 
R

 1EFF : 401-499, 1 23-28-00Page 22 1 1 Aug 01/05 1 1 1CES 1

R  SATCOM LOG Page 
R  Figure 015
 1EFF :  401-499,  1  23-28-00 Page 23 
1  1  Aug 01/05
 1  1
 1CES  1

R  AES ID NOT READY  This status is shown if the AES is awaiting a valid 
R  Aircraft ID. 
R 
R  WAIT USER INPUT  This status is shown while the AES is awaiting input from 
R  the user and is shown in conjunction with the WAITING 
R  inactive advisory. The WAIT USER INPUT state is entered 
R  under any of the following conditions: 
R  - if at power-up the log-on policy in the owner preference 
R  table is USER COMMANDED or 
R  - if a user commanded log-on has failed for any reason or 
R  - if the AES receives a log-on reject due to a permanent 
R  unavailability or 
R  - if the user has selected LOG OFF* or ABORT*. 
R  When in this state, the Satellite ID and, GES ID options 
R  are user enterable. AUTO LOG-ON* is displayed adjacent 
R  to line key 5R. MANUAL* is displayed adjacent to line key 
R  6R. The user may manually select a Satellite/GES for a 
R  manual log-on or may select AUTO LOG-ON* (5R) which causes 
R  the AES to select a GES according to preferences entered in 
R  the GES preference table. 
R 
R  SELECTING SAT  This status is shown while the AES selects a Satellite. 
R 
R  TUNING TO SAT  This status is shown while the AES tunes to and scans 
R  reception from the selected satellite. 
R 
R  SELECTING GES  This status is shown while the AES selects a GES. 
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊1(130)