-BAT 1, BAT 2,
-APU GEN,
-GEN 1, GEN 2,
-EXT PWR.
(4)
In the cockpit, make sure that the warning notices are in position to tell persons not to operate the pushbutton switches on these overhead panels:
-21VU (EMER ELEC PWR section),
-25VU (APU section),
-35VU (ELEC).
Subtask 24-23-55-010-051
B. Get Access
(1)
Make sure that the Third Occupant seat is removed (Ref. TASK 25-11-41-000-001).
(2)
On the L lower side of the panel 120VU, make sure that the access door (8) is removed.
(3)
Make sure that the access platform is in position at the access door 121AL.
(4)
Make sure that the access door 121AL is open.
4. Procedure
_________
**ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,
(Ref. Fig. 401/TASK 24-23-55-991-001) R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 24-23-55-991-001-A)
**ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,
Subtask 24-23-55-420-051
A. Installation of the Contactor Base CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(1)
Install the contactor base (6) in correct position.
(2)
Install the four screws (19) and washers (18) and tighten them.
(3)
Make sure that the electrical cables (14) are clean and in correct condition.
(4)
Install the cables (14).
(5)
Install the nuts (12) and the washers (13) and tighten them.
(6)
If the base has the components that follow:
(a)
Install the three electrical wires (11).
(b)
Install the screws (10) and the washers (9) and tighten them.
(7)
Install the jumpers (17) between the base (6) and the adjacent bases.
(8)
Install the washers (15) and the nuts (16) and tighten them (Ref. TASK 20-21-15-912-001).
Subtask 24-23-55-420-050
B. Installation of the Contactor
(1)
Install the contactor (3) on the 6 tapped barrels (5) of the contactor base (6).
(2)
TORQUE the captive screws (2) to between 0.50 and 0.60 m.daN (44.24 and 53.09 lbf.in).
(3)
Remove the blanking caps from the electrical connector (1) and the electrical receptacle (7).
(4)
Make sure that the electrical connectors are clean and in the correct condition.
(5) Connect the electrical connector (1). R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
Subtask 24-23-55-420-051-A
A. Installation of the Contactor Module CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(1)
Install the contactor module (5) in correct position.
(2)
Install the eight screws (16) and washers (15) and tighten them.
(3)
Make sure that the electrical cables (14) are clean and in correct condition.
(4)
Install the cables (14).
(5)
Install the nuts (13) and the washers (12) and tighten them.
(6)
If the base has the components that follow:
(a)
Install the electrical wires (11).
(b)
Install the screws (10) and the washers (9) and tighten them.
(7)
Install the jumpers (17) between the module (5) and the adjacent modules.
(8)
Install the washers (19) and the nuts (18) and tighten them (Ref. TASK 20-21-15-912-001).
Subtask 24-23-55-420-050-A
B. Installation of the Contactor
(1)
Install the contactor (3) on the module 29XN (5).
(2)
TORQUE the captive screws (2) to between 0.50 and 0.60 m.daN (44.24 and 53.09 lbf.in).
(3)
Remove the blanking caps from the electrical connector (1) and the electrical receptacle (7).
(4)
Make sure that the electrical connectors are clean and in the correct condition.
(5)
Connect the electrical connector (1) to the contactor (3).
R 1EFF : 063-099, 106-149, 153-199, 206-299, 1 24-23-55Page 411 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL
Subtask 24-23-55-710-050 R C. Test of the Contactor
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM ELECTRICAL POWER 電源1(157)
