-
FOR 1000EM2, 4000XU
2XT, 2XU2
Subtask 24-21-49-710-051
G. Test for Oil Leaks
(1)
Do a Dry Motoring Check (Ref. TASK 71-00-00-710-001).
(2)
Make sure that there are no leaks in the IDG oil system.
5. Close-up
________ Subtask 24-21-49-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
-
FOR 1000EM1
437AL, 438AR
-
FOR 1000EM2
447AL, 448AR
(3)
Remove the warning notice(s).
GENERATOR - INTEGRATED DRIVE (IDG) (4000XU) - REMOVAL/INSTALLATION
__________________________________________________________________
TASK 24-21-51-000-040
Removal of the Integrated Drive Generator -IDG 1(2),(4000XU)
WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO ONE HOUR.
WARNING : DO NOT GET ENGINE OIL ON YOUR SKIN FOR A LONG TIME. FLUSH THE OIL
_______ FROM YOUR SKIN WITH WATER. THE OIL IS POISONOUS AND CAN GO THROUGH YOUR SKIN AND IN TO YOUR BODY.
CAUTION : DO NOT USE THE IDG CABLES FOR A HAND HOLD. IF THE IDG CABLES ARE
_______ PULLED LOOSE IT CAN CAUSE DAMAGE TO THE CABLES OR TO THE ENGINE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific plastic bag No specific protective cover No specific protective covers No specific shipping plugs No specific warning notice No specific container 1 USgal (3.7854 l) S387IDG 1 HOIST - ACCESSORY, IDG R/I FOR CFM56-5 TMHSD10-20-00 1 HOIST - ACCESSORY, IDG R/I FOR CFM56-5
1EFF : ALL 1 24-21-51Page 401 1 1 Aug 01/05R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP8002 Material No. 03-002 * lockwire CRS 0.032in. (0.8mm) dia (Ref. 70-30-00)GB DEF-STAN 91-101 LUBRICATING OIL TURBINE ENGINE SYNT BASE (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R R 8 8 8 10 10 10 packing packing packing packing packing packing 24-21-51 02 -12024-21-51 02A-120 24-21-51 02D-12024-21-51 02 -14024-21-51 02A-140 24-21-51 02D-140
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-13-24-680-040 71-13-00-010-040 24-21-51-991-300 Draining of the Oil from the IDGOpening of the Fan Cowl DoorsFig. 401
R **ON A/C 401-499,
R 24-21-51-991-305 Fig. 402
R **ON A/C ALL
R 24-21-51-991-301 Fig. 403
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R **ON A/C 401-499,
R 24-21-51-991-306 Fig. 404 R **ON A/C ALL
3. Job Set-up
__________
Subtask 24-21-51-941-056
A. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the overhead maintenance panel 50VU:
(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源1(80)
