(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice in position to tell persons not to energize the FADEC 1(2).
Subtask 24-21-00-010-066
B. Open the right fan-cowl door (Ref. TASK 71-13-00-010-040):
-
FOR 1000EM1
438AR
-
FOR 1000EM2
448AR
4. Procedure
_________ Subtask 24-21-00-210-059-A
A. Visual Inspection
(1) Do a visual inspection of these components:
NOTE : There can be different signs of possible leakage:
____ -Droplets of oil
-Wet areas around connections, oil stripes on tubes
-Stains or discoloration which can occur when oil or grease is in contact with very hot surfaces.
1EFF : ALL 1 24-21-00Page 611 1 1 Aug 01/05R 1 1 1CES 1
(a)
IDG fittings for leakage:
-Pressure fill port
-Overflow drain port
-Oil-in and oil-out ports (cooling circuit interface with the IDG)
-Case drain. If you find an oil leak, replace the related fitting.
(b)
External oil circuit (oil lines) for leakage and correct condition:
1_ Tubing
- No cracks are permitted on tubes, hoses and tube coupling
nuts.
- There is no limit for the number of nicks and scratches if
the depth is not more than 0.25 mm (0.0098 in.) (after
removal of the high metal).
- Two dents for each tube are permitted if they are of a
smooth contour up to 1.27 mm (0.0500 in.) depth.
You must replace all tubes or hoses that are not in these
limits.
2 Attachment
_
-
Replace broken or cracked brackets.
-
Replace worn clamps.
-Install missing nuts and bolts.
-Tighten loose nuts and bolts.
(c) IDG oil cooler for leakage:
-Oil-in and oil-out ports (cooling circuit interface with the cooler)
-Drain plug
-Body of the cooler. If you find a leak, replace the IDG oil cooler (Ref. TASK 73-11-60-000-002) and (Ref. TASK 73-11-60-400-002).
(2) If you find components wet with oil, make sure that you find and correct all the causes. If necessary, fill the oil tank (Ref. TASK 12-13-24-612-041).
Subtask 24-21-00-210-060
B. Check of the Electrical Circuits
(1)
Make sure that the wiring harnesses are in the correct condition.
(2)
Make sure that the electrical connectors are correctly connected.
1EFF : ALL 1 24-21-00Page 612 1 1 Aug 01/05R 1 1 1CES 1
5. Close-up
________ Subtask 24-21-00-410-066
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the right fan cowl door (Ref. TASK 71-13-00-410-040):
-
FOR 1000EM1
438AR
-
FOR 1000EM2
448AR
(3)
Remove the warning notice(s).
1EFF : ALL 1 24-21-00Page 613 1 1 Aug 01/05R 1 1 1CES 1
TASK 24-21-00-210-043
Torque Check of the Quick Attach-Detach (QAD) Adapter Tension-Bolt
WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO ONE HOUR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 242100-01 To do a torque check of the IDG QAD adapter tension bolt without component removal.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lockwire No specific warning notice No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 03-002 GB DEF-STAN 91-101 LUBRICATING OIL TURBINE ENGINE SYNT BASE (Ref. 20-31-00)
Material No. 05-027 USA MIL-L-81309 RUST INHIBITOR(FOR CORROSION USE 15-004) (Ref. 20-31-00)
1EFF : ALL 1 24-21-00Page 614 1 1 Aug 01/05R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源1(65)
