3. Fault Confirmation
__________________
A. Test Do the functional test of the VOR/MKR (Test of the VOR reception and identification) (Ref. AMM TASK 34-55-00-720-001).
4. Fault Isolation
_______________
A. If on the two NDs:
. the VOR 1 data do not come into view
. the red flag is shown:
- do the BITE test of the VOR/MKR (Ref. AMM TASK 34-55-00-740-002).
(1) If the BITE test gives a maintenance message: R - Do the trouble shooting procedure related to the maintenance R message. R
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-55-00∞∞∞∞∞∞∞∞∞∞Page 220
Feb 01/05 CES (2) If the BITE test does not give a maintenance message:
- replace the RECEIVER-VOR/MKR, 1 (3RS1) (Ref. AMM TASK 34-55-31-000-001) and (Ref. AMM TASK 34-55-31-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the OMNI BEARING AND SIGNAL MKR OUTPUT 2 bus from the VOR/MKR receiver 1 (3RS1) to the first terminal block (Ref. ASM 34-55/01).
B. If on the CAPT ND only: . the VOR 1 data do not come into view . the red flag is shown:
- make sure that on the center pedestal, on the SWITCHING panel 8VU, the EIS DMC selector switch is at CAPT 3:
(1) If no:
- replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the VOR 1/MKR INPUT bus from the DMC 1 (1WT1) to the first terminal block (Ref. ASM 34-55/01).
(2) If yes:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the VOR 1/MKR INPUT bus from the DMC 3 (1WT3) to the first terminal block (Ref. ASM 34-55/01).
C. If on the F/O ND only: . the VOR 1 data do not come into view . the red flag is shown:
- make sure that on the center pedestal, on the SWITCHING panel 8VU, the EIS DMC selector switch is at F/O 3:
(1) If no:
- replace the DMC-2 (1WT2) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the VOR 1/MKR INPUT bus from the DMC 2 (1WT2) to the first terminal block (Ref. ASM 34-55/01).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-55-00∞∞∞∞∞∞∞∞∞∞Page 221
Feb 01/05R
CES (2) If yes:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the VOR 1/MKR INPUT bus from the DMC 3 (1WT3) to the first terminal block (Ref. ASM 34-55/01).
D. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-55-00∞∞∞∞∞∞∞∞∞∞Page 222
Feb 01/05R
CES Loss of the VOR 1 Data on the ND
1. Possible Causes
_______________
- RECEIVER-VOR/MKR, 1 (3RS1)
- ANTENNA-VOR 1/2 (4RS)
- wiring from the VOR 1/2 antenna (4RS) to the VOR/MKR receiver 1 (3RS1)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R ESPM 204416 AMM 34-55-00-720-001 Functional Test of the VOR/MKR AMM 34-55-00-740-002 BITE Test of the VOR/MKR AMM 34-55-11-000-001 Removal of the VOR Antenna 4RS AMM 34-55-11-400-001 Installation of the VOR Antenna 4RS AMM 34-55-31-000-001 Removal of the VOR/MKR Receiver (3RS1, 3RS2) AMM 34-55-31-400-001 Installation of the VOR/MKR Receiver (3RS1, 3RS2) ASM 34-55/01
R
3. Fault Confirmation
__________________
A. Test
(1) Do the functional test of the VOR/MKR (Ref. AMM TASK 34-55-00-720-001).
4. Fault Isolation
_______________
A. If the VOR 1 data do not come into view on the ND:
- do the BITE test of the VOR/MKR (Ref. AMM TASK 34-55-00-740-002).
中國(guó)航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 導(dǎo)航 NAVIGATION 3(149)
