- wiring of the ALTITUDE BUS 2 from the RA transceiver 1 (2SA1) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
AMM 34-42-00-740-002 BITE Test of the Radio Altimeter
AMM 34-42-33-000-001 Removal of the Radio Altimeter Transceiver 2SA1 and
2SA2 AMM 34-42-33-400-001 Installation of the Radio Altimeter Transceiver 2SA1 and 2SA2 ASM 34-42/01
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the radio altimeter (Ref. AMM TASK 34-42-00-740-002) and make sure that the radio altitude indication is shown on the CAPT PFD.
4. Fault Isolation
_______________
A. If the radio altitude indication is not shown on the CAPT PFD:
- replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the RA2 INPUT bus from the DMC1 (1WT1) to the first terminal block (Ref. ASM 34-42/01)
- on the center pedestal, on the SWITCHING panel 8VU, set the EIS DMC selector switch to CAPT 3
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-42-00∞∞∞∞∞∞∞∞∞∞Page 246
Feb 01/05R CES
- make sure that the radio altitude indication is shown on the CAPT PFD.
(a) If the radio altitude indication is shown:
- do a check and repair the wiring of the RA1 INPUT bus from the DMC1 (1WT1) to the first terminal block (Ref. ASM 34-42/01).
(b) If the radio altitude indication is not shown:
- replace the XCVR-RA, 1 (2SA1) (Ref. AMM TASK 34-42-33-000-001) and (Ref. AMM TASK 34-42-33-400-001).
1_ If the fault continues:
- do a check and repair the wiring of the ALTITUDE BUS 2 from
the RA transceiver 1 (2SA1) to the first terminal block
(Ref. ASM 34-42/01).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-42-00∞∞∞∞∞∞∞∞∞∞Page 247
Feb 01/05R
CES Loss of the RA Indication on the F/O PFD
1. Possible Causes
_______________
- DMC-2 (1WT2)
- XCVR-RA, 2 (2SA2)
- wiring of the RA1 INPUT bus from the DMC2 (1WT2) to the first terminal block
- wiring of the RA2 INPUT bus from the DMC2 (1WT2) to the first terminal block
- wiring of the ALTITUDE BUS 2 from the RA transceiver 2 (2SA2) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
AMM 34-42-00-740-002 BITE Test of the Radio Altimeter
AMM 34-42-33-000-001 Removal of the Radio Altimeter Transceiver 2SA1 and
2SA2 AMM 34-42-33-400-001 Installation of the Radio Altimeter Transceiver 2SA1 and 2SA2 ASM 34-42/02
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the radio altimeter (Ref. AMM TASK 34-42-00-740-002) and make sure that the radio altitude indication is shown on the F/O PFD.
4. Fault Isolation
_______________
A. If the radio altitude indication is not shown on the F/O PFD:
- replace the DMC-2 (1WT2) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the RA1 INPUT bus from the DMC2 (1WT2) to the first terminal block (Ref. ASM 34-42/02)
- on the center pedestal, on the SWITCHING panel 8VU, set the EIS DMC selector switch to F/O 3
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-42-00∞∞∞∞∞∞∞∞∞∞Page 248
Feb 01/05R CES
- make sure that the radio altitude indication is shown on the F/O PFD.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(43)
