- replace the radio altimeter transceiver 1.
(2) If the fault continues:
- remove the radio altimeter transceiver 1
- check if the ARINC 600 connectors are in correct condition.
(a) If the ARINC 600 connectors are not in correct condition:
- replace the radio altimeter transceiver 1.
(b) If the ARINC 600 connectors are in correct condition:
- remove the ANTENNA-RA RCPTN, 1 (5SA1) and the ANTENNA-RA XMSN,1 (6SA1) (Ref. AMM TASK 34-42-11-000-001)
- check if the antenna coaxial cables are in correct condition (no corrosion).
1_ If the antenna coaxial cables are not in correct condition:
- replace the coaxial cables.
2_ If the antenna coaxial cables are in correct condition:
- install the radio altimeter transceiver 1
- install the radio altimeter antennas (Ref. AMM TASK 34-42-
11-400-001).
B. Do the test given in para. 3.
Loss of the Interface between Radio Altimeter Antennas and Transceiver 2
1. Possible Causes
_______________
- XCVR-RA, 2 (2SA2)
- ANTENNA-RA RCPTN, 2 (5SA2)
- ANTENNA-RA XMSN, 2 (6SA2)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 34-42-00-740-002 BITE Test of the Radio Altimeter AMM 34-42-11-000-001 Removal of the Radio Altimeter Antennas 5SA1, 5SA2, 6SA1, 6SA2 AMM 34-42-11-400-001 Installation of the Radio Altimeter Antennas 5SA1, 5SA2, 6SA1, 6SA2 AMM 34-42-33-000-001 Removal of the Radio Altimeter Transceiver 2SA1 and 2SA2 AMM 34-42-33-400-001 Installation of the Radio Altimeter Transceiver 2SA1 and 2SA2
3. Fault Confirmation
__________________
A. Test Do the BITE test of the radio altimeter (Ref. AMM TASK 34-42-00-740-002).
4. Fault Isolation
_______________
A. If the test gives no maintenance message:
NOTE : If there is a maintenance message, refer to the related trouble
____ shooting procedure in the applicable Page Block 101.
- swap the XCVR-RA, 2 (2SA2) and the radio altimeter transceiver 1 (Ref. AMM TASK 34-42-33-000-001) and (Ref. AMM TASK 34-42-33-400-001).
(1) If the fault stops:
- replace the radio altimeter transceiver 2.
(2) If the fault continues:
- remove the radio altimeter transceiver 2
- check if the ARINC 600 connectors are in correct condition.
(a) If the ARINC 600 connectors are not in correct condition:
- replace the radio altimeter transceiver 2.
(b) If the ARINC 600 connectors are in correct condition:
- remove the ANTENNA-RA RCPTN, 2 (5SA2) and the ANTENNA-RA XMSN,2 (6SA2) (Ref. AMM TASK 34-42-11-000-001)
- check if the antenna coaxial cables are in correct condition (no corrosion).
1_ If the antenna coaxial cables are not in correct condition:
- replace the coaxial cables.
2_ If the antenna coaxial cables are in correct condition:
- install the radio altimeter transceiver 2
- install the radio altimeter antennas (Ref. AMM TASK 34-42-
11-400-001).
B. Do the test given in para. 3.
R TASK 34-42-00-810-841
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 3(49)
