27-41-51
 ALL  ú ú 01 Page 402 ú Oct 25/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (2) Rig Pin E-1 - 0.309/0.311-inch diameter 6.7 |0.25 inches long
 NOTE: The rig pins are part of kit F70207-69, -78 or -83.
____
 B. References
 (1)
27-41-00/501, Horizontal Stabilizer Trim Control System

 C.
Access

 (1)  
Location Zones
 101 Control Cabin, LH
 102 Control Cabin, RH
 202 Lower Nose Compartment

 (2)  
Access Panels
 1103 Forward Access Door

 D.
Procedure

 S 424-006
 (1)
Install the column cutout switch:

 (a)
Install the mounting bolts (3).

SEE

A 737-300/400/500MAINTENANCE MANUAL
 (b) (c)  Connect the electrical connectors.Connect the rod assembly (1) to the switch arm (2).
 (2)  S 494-007Install the rig pin E-1 through the left forward control quadrant (Fig. 402).
 (3)  S 494-008Install the rig pin ST-4 in the column cutout switch (Fig. 401).
 (4)  S 434-009Adjust the length of the rod assembly (1) until you can easily install the bolt that connects the rod assembly (1) and the switch arm (2). (a) Tighten the rod jamnuts. (b) Install a lockwire.
 (5)  S 094-010Remove the rig pins E-1 and ST-4.
 (6)  S 714-011Do a test of the column cutout switch (AMM 27-41-00/501).
 (7)  S 414-012Close the access door 1103.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-51
 ALL  ú ú 01 Page 404 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 STABILIZER TRIM CONTROL WHEEL - REMOVAL/INSTALLATION
____________________________________________________
 1.  General_______
 A. This procedure has these tasks:
 (1)  
Stabilizer Trim Control Wheel Removal.

 (2)  
Stabilizer Trim Control Wheel Installation.

 TASK 27-41-64-014-003
 2.  Stabilizer Trim Control Wheel Removal (Fig. 401)_____________________________________
 A. Access
 (1)  
Location Zones

 (a)  
101/102 Control Cabin - Left/Right

 B.
Stabilizer Trim Control Wheel Removal

 S 014-008
 (1)  
Remove the stabilizer trim wheel from the control stand:

 (a)  
Remove the bolt that attaches the stabilizer trim control wheel to the shaft.

 (b)  
Remove the stabilizer trim control wheel from the shaft.

 S 014-004
 (2)  
As necessary, remove the upper side cover and lower side cover from the side of the control stand:

 (a)  
Remove the screws and the pocket assembly from the lower side cover.

 (b)  
Remove the screws that attach the upper side cover and the lower side cover to the control stand.

 (c)  
Remove the upper side cover and the lower side cover from the control stand.

 TASK 27-41-64-414-006
 3.  Stabilizer Trim Control Wheel Installation (Fig. 401)__________________________________________
 A. Access
 (1)  
Location Zones

 (a)  
101/102 Control Cabin - Left/Right

 B.
Stabilizer Trim Control Wheel Installation

 S 104-005
 (1)  
As necessary, install the upper side cover and the lower side cover on the control stand:

 (a)  
Install the upper side cover and the lower side cover on the control stand.

 (b)  
Install the screws that attach the upper side cover and the lower side cover to the control stand.

 (c)  
Install the screws in the pocket assembly and the lower side cover.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-64
 ALL  ú ú 01 Page 401 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(106)