曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SLATS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
Set the HYD PUMP B ELEC 1 switch (P5 overhead panel) to ON
 (Ref 27-81-00/201).

 S 865-085-002

 (2)  
Make sure that the flaps are fully retracted.

 S 745-086-002

 (3)  
Do a check of the flap position inputs to the SMC:

 (a)  
Push the down button on the SMC maintenance control panel on the front of each SMC.

 (b)  
Make sure that the display on each SMC shows FLAP DET UP.

 (c)  
Move the flaps to the 1-unit position.

 NOTE: The leading edge flaps and slats will extend as the
____
 trailing edge flaps extend.

 (d)  
Make sure that each display shows FLAP DET 1.

 (e)  
Move the flaps to the 2-unit position.

 (f)  
Make sure that each display shows FLAP DET 2.

 (g)  
Move the flaps to the 5-unit position.

 (h)  
Make sure that each display shows FLAP DET 5.

 (i)  
Move the flaps to the 10-unit position.

 (j)  
Make sure that each display shows FLAP DET 10.

 (k)  
Move the flaps to the 15-unit position.

 (l)  
Make sure that each display shows FLAP DET 15.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH STALL MANAGEMENT ú

 27-32-00
 COMPUTER P/N 65-52822  ú CONFIG 2 ú 05 Page 511 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (m)  
Move the flaps to the 25-unit position.

 (n)
Make sure that each display shows FLAP DET 25.

 (o)  
Move the flaps to the 30-unit position.

 (p)
Make sure that each display shows FLAP DET 30.

 (q)  
Move the flaps to the 40-unit position.

 (r)
Make sure that each display shows FLAP DET 40.

 (s)  
Move the flaps to the UP position.

 M.
Engine Tachometer Inputs Test with Stall Warning System Tester

 NOTE: If you use the stall warning system tester to do the Engine
____ Tachometer Inputs Test, do not do the section below, Engine Tachometer Inputs Test with DC Power Supplies.
 NOTE: The ac signal voltage for the N1 and N2 values is a constant
____ 2.5 |1.0V RMS. You will change the frequency of the ac voltage to
_________
 change the N1 and N2 values.

 S 015-087-002
 (1)  
Open the left and right fan cowl panels on engines 1 and 2 (Ref 71-11-02/201).

 S 035-004-002

 (2)  
Disconnect the electrical connectors D546 from the N1 sensor and D552 from the N2 sensor on each engine.

 S 485-088-002

 (3)  
Connect the stall warning system tester.

 NOTE: Follow the instructions on the lid of the tester box to
____
 connect the tester.

 S 745-089-002
 (4)  
Do a check of the engine N1 tachometer input to the SMC:

 (a)  
Push the down button on each SMC to show the N1 display.

 (b)  
Set the engine No. 1 N1 indicator to 0% (0 Hz) and the engine No. 2 N1 indicator to 0% (0 Hz).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH STALL MANAGEMENT ú

 27-32-00
 COMPUTER P/N 65-52822  ú CONFIG 2 ú 07 Page 512 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (c)  
Make sure that the N1 value on each SMC display is 0 |5%.

 (d)  
Set the engine No. 1 N1 indicator to 80% (2070 |1 Hz) and the engine No. 2 N1 indicator to 80% (2070 |1 Hz).

 (e)  
Make sure that the N1 value on each SMC display is 80 |5%.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(55)