(b)  
Put the flap control lever in the UP detent to retract the flaps.

 (c)  
Do this task: "Depressurize Hydraulic System B" (Ref 27-51-00/201).

 S 485-004
 (3)  
Install the rig pins F-5 and F-6 through the inboard side of the boom (12) to keep the boom roller (11) between the pins.

 (4)
Remove the access panels from the lower surface of the midflap.

 S 015-005
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 01 Page 501 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

1. CABLE

EXHAUST GATE

MEASURED FROM THE CENTER OF THE PUSHROD ATTACH BOLT TO THE MIDFLAP MID SPAR
Inboard Trailing Edge Flap Adjustment Figure 501 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 01 Page 502 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

Inboard Trailing Edge Flap Adjustment
Figure 501 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 01 Page 503 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

|0.06 INCH MAX MISMATCH FWD

A-A

THE PERMITTED CLEARANCE WITH THE FLAPS RETRACTED. THE MINIMUM CLEARANCE THROUGHOUT THE EXTEND/RETRACT CYCLE TO BE 0.02 INCH
Inboard Trailing Edge Flap Adjustment Figure 501 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 01 Page 504 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (5)  S 225-006Examine the position of the bellcrank (2) and the cam arm (6).
 NOTE:____ The bellcrank and the arm will make an angle of approximately 157 degrees with the clutch engaged.
 (a)  If the clutch is not engaged, push the bellcrank to the position shown to engage the clutch.
 NOTE:____ A 350 to 425-pound load at the outboard end of the bellcrank is necessary to disengage the clutch. A small force is necessary to engage the clutch.
 (6)  S 825-007Move the cam roller (7) 0.42 | 0.03 inch from the forward end of the slot as shown: (a) Turn the adjustment screws (13 and 14) to adjust the boom cables. (b) If it is not easy to get the 0.42-inch dimension, you can use a rigging block. 1) You can make the rigging block from a 2.25 inch plastic block. The block must have the shape of the cam slot. 2) Use the tape to hold the rigging block in the cam slot and put the roller against the block.
 (7)  S 835-008Keep the 0.42 inch dimension and adjust the tension on the cables to 100 | 10 pounds.
 NOTE:____ The temperature must be approximately 70°F when you adjust the tension. If the temperature decreases, you must decrease the tension. If the temperature increases, you must increase the tension. Do not change the tolerance to more than the 10 pound limit.
 (8)  S 835-009Adjust the cables (1 and 9) at the turnbuckles until the difference between dimension X and dimension Y is not more than 0.06 inch.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 01 Page 505 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(178)