(b)  
Make a record of each bolt length and location.

 NOTE: You can use this for the installation.
____
 (c)  At the stabilizer rear spar, remove the three bolts (1), washers (2 and 5), and nuts (3).
 NOTE: If it is necessary, adjust the tension in the sling to
____ help remove the mounting bolts.
 (d)  
At the stabilizer front spar, remove the cotter pins, nuts (7), washers (6 and 8) two bolts (11), shims (9 and 10), and washers (12).

 (e)  
Lift the stabilizer outboard section clear of the airplane.

 1)  Move the stabilizer outboard section out horizontally, then lower it to the support stand.
 TASK 27-41-11-404-009
 3.  Horizontal Stabilizer Installation__________________________________
 A.  Special Tools and Equipment
 (1)  F80006-54 or -52 (preferred) - Horizontal Stabilizer Hoisting Sling
 (The -58 cable is used to remove or install the stabilizer without the elevator attached and the -56 cable is used to remove or install the stabilizer with the elevator attached)
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-11
 ALL  ú ú 02 Page 408 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.
E.
F.
A
737-300/400/500MAINTENANCE MANUAL
 (2)  
F71336-501 - Horizontal Stabilizer Trim Lock

 (3)  
C55011-2 - Spanner Wrench - Horizontal Stabilizer

 (4)  
C55002-1 - Punch Set - Horizontal Stabilizer Center Section Hinge

 Pin RemovalStandard Tools and Equipment

 (1)  
Hoist - capable of lifting 700 pounds to 20 foot height

 (2)  
Support Stand - to support the stabilizer after removal

 (3)
Ratchet - 1/2 inch drive - for use with the Spanner WrenchConsumable Materials

 (1)  
D00633 - Grease - BMS 3-33 (Preferred)

 (2)  
D00013 - Grease - MIL-G-23827 (Optional)

 (3)  
A00247 - Sealant - BMS 5-95

 (4)  
C00913, Compound-Corrosion Preventive - BMS 3-27

 (5)
B00624, Compound - Anti-Seize - BMS 3-28References

 (1)  
AMM 27-31-00/501, Elevator and Tab Control System

 (2)
AMM 27-31-11/401, ElevatorsAccess

 (1)  
Location Zone 709 Horizontal Stabilizer, LH 710 Horizontal Stabilizer, RH

 (2)  
Access Panels 3801 Tail Cone Access Door, LH 3802 Tail Cone Access Door, RH

Procedure
 S 494-015
 (1)  
Install the horizontal stabilizer sling (Fig. 404):

 S 644-044

 (2)  
AIRPLANES WITHOUT CRES WASHERS BONDED TO CENTER SECTION LUGS; Apply corrosion preventive compound on the bolt shanks, washers, and all mating surfaces on the front and rear spar bolts.

 NOTE: If you complete SB 55-1058, you do not need to do this step.
____
 S 644-017
 (3)  
Apply a layer of grease to the inner and flange surfaces of the bushings in the front and the rear spar fittings.

 S 394-042

 (4)  
Apply anti-seize compound on bolts threads and nut threads on the front and rear spar bolts.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-11
 ALL  ú ú 01 Page 409 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 864-029
 CAUTION:_______YOU MUST CAREFULLY LIFT THE SLING. A SUDDEN MOVEMENT OF THE SLING CAN CAUSE DAMAGE TO THE STABILIZER.
 (5)  
Lift the horizontal stabilizer to its position.

 S 824-030

 (6)  
Align the stabilizer with the front and rear spar fittings.

 S 424-031

 (7)  
Attach the stabilizer outboard section to the center section:

 (a)
Temporarily install the bolts (11) with the bolt heads aft.

 (b)  
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(91)