(h)  
Connect the hydraulic lines.

 (i)  
Lift the airplane for the nose gear retraction (Ref Chapter 7, Airplane Lifting).

 (j)  
Pressurize the hydraulic system A (Ref 29-15-00, MP).

 WARNING: REMOVE THE EQUIPMENT AND PERSONS FROM THE WHEEL WELL AREAS
_______ BEFORE YOU OPERATE THE GEAR. IT CAN PREVENT INJURY TO PERSONS AND DAMAGE TO STRUCTURE.
 (k)  
Remove the ground lock assemblies.

 (l)  
Operate the gear retraction for several times to bleed air from the package and the lines.

 WARNING: MAKE SURE YOU INSTALL THE GROUND LOCK ASSEMBLIES IN THE
_______ MAIN LANDING GEAR TO PREVENT THE ACCIDENTAL OPERATION OF THE GEAR. IT CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT IF THE GEAR RETRACTS.
 (m)  
Examine the hydraulic connections for leakage.

 (n)  
Extend the gear.

 (2)  
Lower the airplane and remove the jacks.

 S 844-006
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-33-31
 ALL  ú ú 01 Page 403 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 NOSE GEAR TRANSFER CYLINDER - REMOVAL/INSTALLATION
__________________________________________________
 TASK 32-33-41-004-001
 1.  Nose Gear Transfer Cylinder Removal (Fig. 401)___________________________________
 A. Equipment
 (1)  
Ground Lock Assemblies (AMM 32-00-01).

 B.
Prepare for the removal.

 S 864-002
 (1)  
Make sure that you install the ground lock assemblies for the landing gears (AMM 32-00-01).

 (a)  
Decrease the pressure from the hydraulic system (AMM 29-15-00/201).

 C.
Procedure

 S 034-003
 (1)  
Disconnect and seal the hydraulic lines that attach to the cylinder.

 (a)  
Loosen the clamp bolts until you can remove the transfer cylinder.

 (b)  
Remove the cylinder from the airplane.

 (c)  
Remove the hydraulic unions.

 (d)  
Discard the O-ring packings.

 NOTE: Put a plug on the ports.
____
 TASK 32-33-41-404-004
 2.  Nose Gear Transfer Cylinder Installation (Fig. 401)________________________________________
 A. Equipment
 (1)  
Ground Lock Assemblies (AMM 32-00-01).

 B.
Consumable Materials

 (1)  
Hydraulic Fluid - BMS 3-11 (AMM 20-30-21)

 C.
Procedure

 (1)  
Remove the plugs.

 S 434-006

 (2)  
Install the hydraulic unions in the transfer cylinder with new O-ring packings.

 (a)  
Fill the transfer cylinder from the two ends with hydraulic fluid.

 S 844-005
 NOTE: Put a cap on the unions.
____
 (b)  Put the transfer cylinder in the clamps.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-33-41
 ALL  ú ú 01 Page 401 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 
737-300/400/500MAINTENANCE MANUAL
 (c)  Adjust the position of the cylinder until you align the
 hydraulic lines.
 (d)  Remove the caps.
 NOTE:____ Put a plug and connect the hydraulic lines with your
 hand.
 (e)  Tighten the clamps and hold the cylinder.
 (f)  Tighten the hydraulic lines.
 (g)  Lift the airplane for the nose gear retraction (Ref Chapter 7,
 Airplane Lifting).
 (h)  Pressurize the hydraulic system A (AMM 29-15-00/201).

 WARNING: REMOVE ALL EQUIPMENT AND PERSONS FROM THE WHEEL WELL AREAS
_______ BEFORE YOU OPERATE THE GEAR. IT CAN PREVENT INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (i)  
Remove the ground lock assembly (AMM 32-00-01).

 (j)  
Operate the gear retraction several times to bleed the air from the cylinder and the lines.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(117)