S 984-086

 (32)
 Move the assembly of the pressure seal (24) on the cables at the end of the left trunnion pin (20).

 S 434-110

 (33)
 Put the assembly of the pressure seal in and together with ring (25), move the seal into the left trunnion pin (20) until the seal will contact the stop.

 S 624-142
 WARNING: USE NITRILE GLOVES FOR SKIN PROTECTION AGAINST BMS 3-27
_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
 CAUTION: REMOVE UNWANTED MASTINOX FROM SURFACES WHICH WILL BE
_______ LUBRICATED. IF YOU APPLY MASTINOX TO JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT COULD OCCUR.
 (34)
 Apply a layer of the corrosion preventive compound to the trunnion pin nut (19) (AMM 12-21-21/301).

 S 434-050

 (35)
 Install the trunnion pin nut (19) on the inboard end of the left trunnion pin (20).

 S 434-051

 (36)
 Use the spanner wrench to tighten the trunnion pin nut (19) to 100 -150 pound-inch lube torque.

 (a)  
If it is necessary, loosen the nut to adapt with the vernier of the lock holes.

 S 434-052
 (37)
 Install the nut lock (21) on the inboard side of the left trunnion pin (20).

 (38)
 Install the cap screw (22) to attach the nut lock (21).

 (39)
 Install the lockwire on the cap screw (22).

 S 434-111
 S 434-112
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-00
 ALL  ú ú 02 Page 413 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 224-077
 (40) Examine that the seal assembly will turn freely from the extended cable position of the gear to a simulated gear retracted cable position.
 NOTE: This step will verify that the cables will not become twisted
____
 when the gear is retracted.

 S 624-143
 WARNING: USE NITRILE GLOVES FOR SKIN PROTECTION AGAINST BMS 3-27
_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
 CAUTION: REMOVE UNWANTED MASTINOX FROM SURFACES WHICH WILL BE
_______ LUBRICATED. IF YOU APPLY MASTINOX TO JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT COULD OCCUR.
 (41)
 Apply a layer of corrosion preventive compound to the outer side of the lower bolt (9) of the drag brace (AMM 12-21-21/301).

 S 434-113

 (42)
 Install the nylon washer (7) on the bearing in the lower link (8) of the drag brace.

 S 434-115

 (43)
 Connect the lower link (8) into the fitting (5) on the shock strut.

 S 434-116

 (44)
 Install the lower bolt (9) of the drag brace.

 (45)
 Install the flat washer (6) and the nut.

 (46)
 Tighten the nut 550 to 700 pound-inch lube torque.

 S 434-119

 (47)
 Install the cotter pin.

 G.
Put the Airplane in Its Usual Condition

 S 434-117
 S 434-118
 S 414-062
 (1)  Install the aft access panel on the left and right bulkheads of the nose wheel well.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-00
 ALL  ú ú 01 Page 414 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (2)  S 434-061Connect the electrical plug for the taxi light of the nose landing gear to the electrical connection.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(16)