B.
References
(1)
29-15-00/201, Hydraulic Systems A, B, and Standby
(2)
32-31-00/501, Landing Gear Control System
(3)
32-32-00/501, Main Gear Extension and Retraction
C.
Access
(1)
Location Zone
216,217 Main Landing Gear Wheel Well
D.
Installation
(1) S 434-007Install the hydraulic fittings and the new O-rings in the selector valve.
NOTE:____ You must lubricate the O-rings with hydraulic fluid.
(2) S 614-008Fill the selector valve with hydraulic fluid.
NOTE:____ Seal the ports of the selector valve with a cap.
(3) S 424-009Put the selector valve in its position and install the attach bolts.
(4) S 864-024Move the control lever for the landing gear to the OFF position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-31-51
ALL ú ú 01 Page 403 ú Jul 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 434-026
(5) Install rig pin or .309 - .311 inch diameter rod.
NOTE: If the rig pin is not free, adjust the cable system
____
(AMM 32-31-00/501).
S 434-012
(6)
Connect the actuating link to the selector valve.
S 434-013
(7)
Remove the caps from the selector valve and connect the hydraulic lines to the valve.
S 714-014
(8)
Do a test of the control system for the landing gear (Ref 32-31-00/501).
S 714-020
(9)
Do a test of the main landing gear only (Ref 32-32-00/501).
NOTE: If you cannot lift the airplane for the test, do the
____
other landing gear test.
S 794-021
(10) Make sure the hydraulic connections do not have leaks.
TASK 32-31-51-704-027
3. Other Landing Gear Test
________________________
A. Procedure
S 714-028
(1)
If you cannot lift the airplane to do the usual test of the main landing gear, do this test:
(a)
Make sure these parts are correctly installed: 1) Selector Valve 2) Actuating Link 3) Hydraulic Lines
WARNING: MAKE SURE THE GROUND LOCK ASSEMBLIES ARE INSTALLED IN THE
_______ LANDING GEAR TO PREVENT OPERATION OF THE LANDING GEAR. INJURIES TO PERSONS AND/OR DAMAGE TO EQUIPMENT CAN OCCUR IF THE LANDING GEAR RETRACTS.
(b) Pressurize hydraulic system A (Ref 29-15-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-31-51
ALL ú ú 01 Page 404 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(c) Move the control lever for the landing gear from DN to UP and back three times.
NOTE:____ You must use the override switch to do this.
NOTE:____ Hold the lever in each position for three seconds before you move the lever to the subsequent position.
(d) (e) (f) (g) (h) (i) Move the control lever for the landing gear to DN.Make sure the inboard end of the actuator for the main landing gear tries to extend when you move the control lever from DN to OFF.Move the control lever for the landing gear to DN.Do a check for hydraulic leakage with the hydraulic pressure applied.Release the pressure from hydraulic system A (Ref 29-15-00/201).Make sure the hydraulic connections do not have leaks.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-31-51
ALL ú ú 01 Page 405 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(56)
