8. DRAG BRACE
 UPPER LINK  10. WASHER 
9. PIN  11. SPACER 
BUSHING 
15. WASHER 

6. LOCK LINK
12.
 SPACER BUSHING

13.
 DRAG BRACE

 LOWER LINK FWD
14. BOLT
C
Nose Gear Lock Mechanism Installation Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-33-51
 ALL  ú ú 01 Page 403 ú Jul 15/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (g)  
Disconnect the electrical conduit(s) from the lock brace.

 (h)  
Move the lock brace (3) up until you get access to the actuator upper attachment.

 (i)  
Hold the lock actuator (16).

 (j)  
Remove the bolt (18).

 (k)  
Disconnect the actuator from the lock brace.

 (l)  
Remove the nuts (7) and washers from the spring retainer bolts.

 (m)  
Remove the springs (1) and (5).

 (n)
Put the nuts (7) on the spring retainer bolts.

 NOTE: Tighten the bolts with your hand.
____
 (o)  Remove the lock strut which has the lock brace (3) and the lock link (6) as a completed assembly.
 TASK 32-33-51-404-004
 2.  Nose Gear Lock Mechanism Installation (Fig. 401)_____________________________________
 A. Standard Tool
 (1)  
Feeler Gage

 B.
Consumable Materials

 (1)  
Solvent - P-D-680 (AMM 20-30-41)

 (2)  
Compound - Corrosion Inhibiting, BMS 3-27, Mastinox 6856K

 (3)  
D00633 Grease - BMS 3-33

 (4)  
D00013 Grease - MIL-PRF-23827

 (5)  
Adhesive - BMS 5-95 (AMM 20-30-11)

 C.
Procedure

 S 864-010
 WARNING: USE NITRILE GLOVES FOR SKIN PROTECTION AGAINST BMS 3-27
_______ (MASTINOX 6856K). IF THE MASTINOX GETS ON YOUR SKIN, REMOVE IT WITH WATER IMMEDIATELY. IF THE MASTINOX GETS IN YOUR EYES, FLUSH YOUR EYES WITH WATER IMMEDIATELY AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURY TO PERSONS.
 CAUTION: REMOVE THE UNWANTED MASTINOX FROM SURFACES WHERE YOU LUBRICATE.
_______ IF YOU APPLY MASTINOX TO THE JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT CAN OCCUR.
 (1)  
Clean all components:

 (a)  
Lubricate all components with grease just before the assembly.

 NOTE: Do not include the shaft (19) and the bolt (14).
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-33-51
 ALL  ú ú 02 Page 404 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Apply grease on parts.
 NOTE: Apply a layer of Mastinox 6856K to the parts where you
____ do not lubricate with the grease after the installation.
 NOTE: Apply a layer of MIL-PRF-23827 or the preferred grease
____ BMS 3-33 where you lubricate with the grease after the installation (AMM 12-20-00/301).
 D. Procedure
 S 424-014
 CAUTION: DO NOT TRY TO ADJUST THE CLEARANCES THAT AFFECT THE DISTANCE
_______ THE LOCK LINK-LOCK BRACE ASSEMBLY CAN MOVE OVER-CENTER WHEN THE ASSEMBLY IS INSTALLED ON THE AIRPLANE. THE ADJUSTMENT TO GET THE CORRECT AMOUNT OF OVER-CENTER TRAVEL MUST BE COMPLETED IN ACCORDANCE WITH THE APPLICABLE OVERHAUL MANUAL OR COMPONENT MAINTENANCE MANUAL PROCEDURE.
 (1)  
Install the lock-link brace assembly (3, 6):

 (a)  
Apply a thin layer of the corrosion preventive compound, Mastinox 6856K, to the lock brace shaft (19).

 (b)  
Put the lock brace (3) in the fitting (20).

 (c)
Install the shims used in the initial installation.

 (d)  
Install the shaft (19).

 NOTE: If you replace the lock strut or one of the lock strut
____ components, examine the clearance between the lock brace and the fitting (20) with the two ends of the lock strut attached. Keep a clearance of 0.000 to 0.005 inch between the lock brace and the fitting. If it is necessary, install the shims.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(119)