TORQUE LB-INCHES (NEWTON-METERS)
870-1300 (98.3-146.9) 250-350 (28.3-39.6) 100-150 (11.3-17.0) 870-1300 (98.3-146.9)

FRONT VIEW OF HINGE SUPPORT
FITTINGS ON PIVOT BULKHEAD

(RIGHT INSTALLATION IS SHOWN,
LEFT INSTALLATION IS OPPOSITE)

LOCATION  BOLT  WASHERS  NUT
UNDER HEAD  UNDER NUT 

J A B C D E F G H I  BACB30US8K36 BACB30UU7K13 BACB30UU5K13 BACB30US8K36 BACB30UU7K13 BACB30UU5K14 BACB30UU6K14 BACB30UU10K27D BACB30UU5K13 BACB30US10K18  BACW10BP8C AN960JD716 AN960JD516 BACW10BP8C AN960JD716 AN960JD516 AN960JD516 AN960JD1016 AN960JD616 AN960JD1016  BACW10BP8P BACW10BP8P AN960JD1016  BACN10HR8CD BACN10JC7CD BACN10JC5CD BACN10HR8CD BACN10JC7CD BACN10JC5CD BACN10JC5CD BACN10JC10CD BACN105C6CD MS24665-374 

ATTACHMENT BOLT LOCATIONS
Attachment of Stabilizer Hinge Support Fittings on Pivot Bulkhead
Figure 203

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-02
 ALL  ú
 ú  05  Page 212
 ú  Feb 18/00 

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Remove the spacer (19).

 (c)  
Remove the retaining nut (3) and the washer (1).

 (d)  
Install the replacement tool that has the attachments for the hinge bearing removal (Fig. 202).

 (e)  
Remove the hinge bearing (15) from the bearing retainer.

 TASK 27-41-02-402-026
 5.  Stabilizer Hinge Installation (Fig. 201)_____________________________
 A. Special Tools and Equipment
 (1)  
2MIT65B03670 - Horizontal Stabilizer Hinge Bolt and Bearing Replacement Tool (which is referred to as the "replacement tool")

 (2)  
G27036-46 - Horizontal Stabilizer Hinge Bearing Free Play Check Tool (which is referred to as the "check tool")

 NOTE:____Use this tool with shear deck fittings (Fig. 201). Use the tool only in an area that has no high winds.
 B. Consumable Materials
 (1)  
D00633 Grease - BMS 3-33 (Preferred)

 (2)  
D00013 Grease - MIL-G-23827 (Optional)

 C.
References

 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 27-41-02/601, Stabilizer Hinge

 (3)  
AIPC 55-10-50-01

 D.
Access

 (1)  
Location Zone 311 Area Aft of Pressure Bulkhead, LH 312 Area Aft of Pressure Bulkhead, RH 315 Area Aft of Stabilizer Box Compartment, LH 316 Area Aft of Stabilizer Box Compartment, RH

 (2)  
Access Panel
 315A Access Door

 E.
Install the Stabilizer Hinge Bearing

 S 222-027
 (1)  
Do this task: "Horizontal Stabilizer Hinge Wear Limits Inspection" (AMM 27-41-02/601).

 S 282-028

 (2)  
Make sure the retaining nut (2), on the outboard side of the bearing retainer housing, is tight and installed with a lockwire and the washer (2A).

 S 422-029

 (3)  
Install the hinge bearing (15):

 (a)  
Apply a thin layer of grease (BMS 3-33 or MIL-G-23827) on the outer surface of the hinge bearing (15).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-02
 ALL  ú ú 02 Page 213 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Use the replacement tool (Fig. 202) to install a replacement hinge bearing (15).

 (c)  
Install the washer (3A) and the retaining nut (3) on the inboard side of the bearing retainer housing. 1) Use the spanner wrench to tighten the retaining nut (3) to

 200-300 pound-inches (22.6-33.9 newton-meters). 2) Install a lockwire on the retaining nut (3).
 F. Install the Stabilizer Hinge Support Fittings (Fig. 201)
 S 282-030
 (1)  Make sure the support fitting (14) of the inboard side of the hinge has the support fitting (14), the bushing (4), the adjustment screw (6), the washer (4A), and the nut (5).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(147)