EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-03
ALL ú ú 04 Page 403 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
D. Remove the Nonreaction Hinge
S 034-010
(1)
Remove the hinge bolt (6) and the bushings (3).
S 024-011
(2)
Remove the bolts (1) which attach the hinge to the elevator front spar.
S 024-056
(3)
Move the hinge from supporting hinge fittings down to disengage it.
TASK 27-31-03-404-012
3. Nonreaction Hinge Installation (Fig. 401)______________________________
A. Consumable Materials
(1)
D00013 Grease - MIL-G-23827
B.
References
(1)
AMM 06-09-06/201, Stabilizer and Elevator Access Doors and Panels
(2)
AMM 24-22-00/201, Manual Control
(3)
AMM 27-31-03/601, Elevator Hinges
(4)
AMM 29-11-00/201, Main Hydraulic Supply System
(5)
IPC 29-31-09, Fig. 1
(6)
IPC 55-20-03, Fig. 1
(7)
IPC 55-20-04, Fig. 1
C.
Access
(1)
Location Zone
335 Inboard Elevator, LH
345 Inboard Elevator, RH
336 Outboard Elevator, LH
346 Outboard Elevator, RH
(2)
Access Panel 335BBL Leading Edge Hinge Maintenance Access Door 345BBR Leading Edge Hinge Maintenance Access Door 335JBL Leading Edge Hinge Maintenance Access Door 345JBR Leading Edge Hinge Maintenance Access Door 336BBl Leading Edge Hinge Maintenance Access Door 346BBR Leading Edge Hinge Maintenance Access Door 336JBL Leading Edge Hinge Maintenance Access Door 346JBR Leading Edge Hinge Maintenance Access Door 336MBL Leading Edge Hinge Maintenance Access Door 346MBR Leading Edge Hinge Maintenence Access Door 336QBL Leading Edge Hinge Maintenence Access Door 346QBR Leading Edge Hinge Maintenance Access Door
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-03
ALL ú ú 01 Page 404 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
NONREACTION HINGE (4 LOCATIONS)
SEE A
1
2 NONREACTION HINGE
3
(6 LOCATIONS) 7 SEE A 8
456
9 10
____ LEFT ELEVATOR SHOWN. RIGHT ELEVATOR OPPOSITE.
NOTE:
1. BOLT (4 LOCATIONS)ELEVATOR FRONT SPAR
3. SLEEVE
BUSHING
8. SMALL
WASHER
19. FLANGED BUSHING
2.
ELEVATOR HINGE ASSEMBLY
3.
SLEEVE BUSHING
7. NUT
4.
LARGE WASHER(S)
5.
LOCK-AS REQUIRED
4. LARGE WASHER
WASHER(S)
AS REQUIRED
6. BOLT
HINGE FITTING BONDING JUMPER
A
Elevator Nonreaction Hinge Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-03
ALL ú ú 01 Page 405 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
D. Install the Nonreaction Hinge
S 224-013
(1)
Examine the hinge and the hinge fittings for worn parts
(AMM 27-31-03/601).
(a)
Replace the part if it is worn.
S 424-014
(2)
Install the nonreaction hinge:
(a)
Align the hinge with the holes on the elevator front spar.
(b)
Install the bolts (1) and washers.
(c)
Tighten the bolts (1) equally.
(d)
Apply a layer of grease to each bushing (3).
(e)
Clean the mating surfaces for the bonding jumpers.
(f)
Install the bushing in the hinge fitting.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(40)
