EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-06
ALL ú ú 01 Page 408 ú Feb 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(c)
Move the halves of the two split retaining rings (3) apart. 1) Remove the split retaining rings (3).
(d)
Remove the upper gimbal pins (7 and 8). 1) Keep the bushing (4) from each gimbal pin locating screw.
S 034-019
(7)
Disconnect the lower gimbal retaining pins (Fig. 402):
(a)
Remove the retaining bolts (14) from the ends of the lower gimbal safety shaft (20).
(b)
Remove the lower gimbal safety shaft (20).
(c)
Remove the retaining pin bolts (24)
(d)
Remove the support brackets of the hydraulic tubing if it is necessary.
(e)
Make sure the hoist holds the weight of the mechanism.
CAUTION: DO NOT USE METAL TOOLS TO REMOVE THE LOWER GIMBAL
_______ RETAINING PIN. DAMAGE TO THE CASING AND THE PIN FLANGES OF THE TRIM DRIVE MECHANISM CAN OCCUR.
(f) Remove the lower gimbal retaining pin (16). 1) Make sure the mechanism is stable. 2) Remove the lower gimbal retaining pins.
a) Use wood wedges below the pin flanges to start the removal. b) Use a rubber mallet to continue the removal.
S 024-020
(8)
Remove the mechanism:
(a)
Move the mechanism clear of the actuator fitting on the stabilizer and the attachment lugs.
(b)
Move the mechanism through the access door 312A and lower it to the stand.
TASK 27-41-06-404-022
3. Stabilizer Trim Drive Mechanism Installation
____________________________________________
A. Special Tools and Equipment
(1)
OHME65B80713-1 - Horizontal Stabilizer Jackscrew Gearbox Hoist Equipment
(2)
ME65B80713-1 - Jackscrew Gearbox Ball Nut Lock
(3)
FME65B80713-1 - Horizontal Stabilizer Actuator Stand
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-06
ALL ú ú 01 Page 409 ú Feb 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(4)
G27030-1 - Horizontal Stabilizer Actuator Torque Adapter
B.
Standard Tools and Equipment
(1)
Hoist - C.M. Puller Model B, Code No. 4043, 3/4-ton capacity, minimum hook distance 10-3/4 inches, maximum lift 30 feet (or equivalent) Columbus McKinnon Corporation C-M Hoist Division 140 John James Audubon Pkwy Amherst, New York 14228-1197 Telex: 6854301 FAX: (716) 689-5645
(2)
Torque Wench - 1/2", 0-50 ft/lb capacity
C.
Consumable Materials
(1)
D00633 Grease - BMS 3-33 (Preferred)
(2)
D00013 Grease - MIL-G-23827 (Optional)
D. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 402 | 1 | Washer | 27-41-06 | 01 | 106 | | | 2 | Nut | | | 111 | | | 3 | Ring - Split Retaining | | | 116 | | | 4 | Bushing | | | 131 | | | 5 | Washer | | | 126 | | | 6 | Nut | | | 121 | | | 7 | Pin - Upper Gimbal, Inner | | | 146 | | | 8 | Pin - Upper Gimbal, Outer | | | 151 | | | 10 | Bolt | | | 101 | | | 12 | Pin | | | 5 | | | 13 | Washer | | | 10 | | | 14 | Bolt - Safety Retaining | | | 351 | | | 15 | Washer | | | 356 | | | 16 | Pin - Retaining, Lower Gimbal | | | 396 | | | 17 | Support | | | 401 | | | 18 | Washer | | | 386 | | | 19 | Nut | | | 391 | | | 20 | Shaft - Safety, Lower Gimbal | | | 366 | | | 21 | Washer | | | 356 | | | 22 | Nut | | | 361 | | | 23 | Washer | | | 381 | | | 24 | Bolt | | | 376 | | | | | | | | 2......…........…...................................…...........….....…........1
E. References
(1)
AMM 06-09-05/201, Body Section 48 Access Doors and Panels
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(175)
