Horizontal Stabilizer Trim Drive Mechanism Hydraulic Brake Installation
Figure 401 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-05
 ALL  ú ú 01 Page 403 ú Jun 10/89
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-005
 (4)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P7, Overhead Circuit Breaker Panel
 1) 7E7, L STAB TRIM S/O VLV
 2) 7E20, R STAB TRIM S/O VLV

 S 014-006
 (5)  
Open the access door 312A (AMM 06-09-05/201).

 S 034-007

 (6)  
Disconnect the hydraulic lines H1, H2, and H3 at the hydraulic brake (4).

 S 034-037

 (7)  
If you replace the hydraulic brake (4) with a new unit, remove the adapter (6).

 (a)  
Keep the adapter (6) for the installation of the hydraulic brake.

 S 034-008
 (8)
Seal all hydraulic lines with plugs and all ports with caps.

 S 024-009

 (9)  
Remove the hydraulic brake (4):

 (a)  
Remove the fasteners (3).

 (b)  
Disengage the hydraulic brake (4) from the differential brake shaft.

 (c)  
Lift the hydraulic brake (4) vertically.

 (d)  
Remove the hydraulic brake (4).

 (e)  
Remove the O-rings (1) and discard them.

 TASK 27-41-05-404-010
 3.  Stabilizer Trim Hydraulic Brakes Installation (Fig. 401)_____________________________________________
 A. Consumable Materials
 (1)  
D00633 Grease - BMS 3-33 (Preferred)

 (2)  
D00013 Grease - MIL-G-23827 (Optional)

 (3)  
C00259 Primer, Corrosion Inhibiting - BMS 10-11, type I

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-05
 ALL  ú ú 01 Page 404 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 B. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | O-Ring | 27-41-06 | 01 | 195 | | | 3 | Nut | | | 51 | | | 4 | Brake - Hydraulic | | | 36 | | | 5 | Washer | | | 46 | | | 6 | Adapter | | | 21 | | | 7 | Nut | | | 26 | | | 8 | Packing | | | 31 | | | 9 | Bolt | | | 41 | | | | | | | | 2......…........…...................................…...........….....…........1
 C. References
 (1)  
AMM 06-09-05/201, Body Section 48 Access Doors and Panels

 (2)  
AMM 24-22-00/201, Manual Control

 (3)  
AMM 29-11-00/201, Main Hydraulic Supply System

 D.
Access

 (1)  
Location Zone
 311 Area Aft of Pressure Bulkhead, LH
 312 Area Aft of Pressure Bulkhead, RH

 (2)  
Access Panel 312A Horizontal Stabilizer Jackscrew Access Door

 E.
Install the Hydraulic Brakes

 S 144-011
 (1)  
Clean open areas of the differential brake shaft.

 S 644-012

 (2)  
Apply a large quantity of grease (BMS 3-33 or MIL-G-23827) to the open areas of the differential brake shaft.

 (3)
Install a new O-ring (1) on the differential brake shaft (2).

 S 864-014

 (4)  
Make sure the mating surfaces of the brake mounting flange and the bull gear housing cover are clean.

 S 824-015

 (5)  
Align the brake mounting flange with the studs.

 (a)  
Engage the internal brake shaft splines with the splines on the differential brake shaft.

 S 434-013
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(170)