27-31-02
 ALL  ú ú 01 Page 411 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (6)  S 864-026Move the elevator to the neutral position.
 (7)  S 434-027Install the input control rod bolt (37) with the bolt head outboard in the input control rod.
 (8)  S 434-028Install the washer (38) and the nut (39). (a) Tighten the nut (39).
 (9)  S 094-029Remove the support from the outboard elevator PCP.
 S 434-030

 (10)
 Install the bolt (18), washer (19), and nut (20) to connect the control rod (17) to the elevator front spar.

 (a)  
Tighten the nut (20).

 S 644-031
 (11)
 Lubricate the elevator (Ref 12-21-18/301).

 S 414-032

 (12)
 Install these access panels (AMM 06-09-06/201):

 (a)  
334LB, 336BB, 336DB, 336JB, 336MB and 336QB for the left outboard elevator.

 (b)  
344LB, 346BB, 346DB, 346JB, 346MB and 346QB for the right outboard elevator.

 S 094-033
 (13)
 Remove the sling from the elevator (Fig. 401):

 (a)  
Remove the sling bolts and fittings.

 (b)  
Install the bolts.

 S 864-036
 (14)
 Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P7, Overhead Circuit Breaker Panel 1) 7E7, L STAB TRIM S/O VLV 2) 7E20, R STAB TRIM S/O VLV

 (b)  
P180, DC Power Distribution Panel 1) 180E7, ELEV/RUD VLV SYS 2 2) 180E22, ELEV/RUD VLV SYS 4 3) 180H8, ELEV/RUD VLV SYS 1 4) 180H23, ELEV/RUD VLV SYS 3

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-02
 ALL  ú ú 01 Page 412 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-038
 (15)
 Set the STAB TRIM 2 and 3 switches on the control stand to ON.

 S 864-039

 (16)
 Set all FLT CONTROL HYD POWER TAIL switches on the P461 Pilots' Overhead Maintenance Panel in NORM.

 S 094-048

 (17)
 Remove the safety device from the receptacle on the top surface of the horizontal stabilizer.

 S 714-049

 (18)
 Do the Outboard Elevator Movement Test in the Operational Test -Elevator Control System (AMM 27-31-00/501).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-02
 ALL  ú ú 01 Page 413 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ELEVATOR HINGE - REMOVAL/INSTALLATION
_____________________________________
 1.  General_______
 A.  There are four tasks in this procedure. There is one task for the removal and one task for the installation of the elevator nonreaction hinges. Also there is one task for the removal and one task for the installation of the elevator reaction hinges. The procedure has these parts:
 (1)
The preparation for the removal of the elevator nonreaction hinge

 (2)
The removal of the nonreaction hinge

 (3)
The installation of the replacement nonreaction hinge

 (4)
The operational test of the nonreaction hinge

 (5)
The preparation for the removal of the elevator reaction hinge

 (6)
The removal of the reaction hinge

 (7)
The installation of the replacement reaction hinge

 (8)
The operational test of the reaction hinge.

 B.  
Each of the elevator hinges can be replaced one at a time. If the replacement of two or more of the adjacent hinges are necessary, they must be replaced one at a time. No more than two nonadjacent hinges can be removed at one time.

 C.  
The removal and installation procedure is the same for the inboard or the outboard elevator hinges.

 D.  
The hinges at the elevator power control packages (PCPs) are identified as the inboard and outboard elevator reaction hinges. The remaining hinges are identified as nonreaction hinges and have numbers from 1 to
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(38)