曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

control guidance systems which are certified for landing operations.
MANUAL FLIGHT CONTROL AIRPLANE TYPE GUIDANCE SYSTEMS
(M/M/S) MANUFACTURER MODEL
b. Special Limitations.
(1) The certificate holder shall conduct all operations authorized by this paragraph in accordance
with applicable Section of the CCAR and the airworthiness certification basis of the manually
flown flight control guidance system being used.
(2) The certificate holder shall not conduct landing operations to any runway using these
systems, unless the certificate holder determines that the flight control guidance system being
used permits safe manually flown approaches and landings to be conducted at that runway.
(3) The certificate holder shall not conduct any operations authorized by this paragraph, unless
the certificate holder’s approved training program provides training in the equipment and
special procedures to be used.
(4) Except when operations are performed under the supervision of a properly qualified check
airman, any pilot used by the certificate holder to conduct manually flown approaches and
landings using these systems must be qualified for the operation being conducted in
accordance with the certificate holder’s approved training program.
c. These operations may be conducted on any ILS facility but only in CAT I or better weather unless
prior coordination with ATC was done by the certificate holder to ensure the protection of the
critical areas.
CIVIL AVIATION
ADMINISTRATION
OF CHINA CCAR-121 / 135 OPERATIONS SPECIFICATIONS
CAAC DOCUMENT
APPROVAL NO
AC-121-001R1
(Company Name) C0027-2 Certificate No:
Effective Date: Y M D
1. Issued by (Branch Name) ,Regional Administration of CAAC
2. These Operations Specifications are approved by direction of CAAC
Principal Operations Inspector: (Name & Signature of POI)
3. Date Approval is effective (Y/M/D) Amendment Number:
4. The certificate holder hereby accepts and receives the Operations Specifications in this
paragraph.
Certificate Holder Representative: (Name & Signature)
Position: Date(Y/M/D):
CIVIL AVIATION
ADMINISTRATION
OF CHINA CCAR-121 / 135 OPERATIONS SPECIFICATIONS
CAAC DOCUMENT
APPROVAL NO
AC-121-001R1
(Company Name) C0029-1 Certificate No:
Effective Date: Y M D
C0029 PUBLISHED RNAV INSTRUMENT APPROACH OPERATIONS USING AN AREA NAVIGATION SYSTEM
The certificate holder is authorized to conduct published RNAV instrument departure, arrival and
approach procedures using area navigation systems to the airports and runways approved for such
operations in these operations specifications and shall conduct all such operations in accordance with
the provisions of these operations specifications.
a. Authorized Aircraft and Equipment. The certificate holder is authorized to conduct instrument
approach operations using the following aircraft and area navigation systems.
AREA AIRPLANE NAVIGATION SYSTEMS
(M/M/S) MANUFACTURER MODEL
b. Special Limitations.
(1) The certificate holder shall not conduct any operation authorized by this paragraph,
unless the certificate holder's approved training program provides training in the
equipment and special procedures to be used.
(2) A flight crewmember shall not conduct operations authorized by this paragraph until
that crewmember has successfully completed the certificate holder's approved
training program. The crewmember must be certified as qualified (by one of the
certificate holder's check airmen or an CAAC inspector) for instrument approach
operations using the installed area navigation system.
(3) During the initial 6 months of operation with a particular aircraft and area navigation
system combination, the certificate holder shall not use IFR approach and landing
minimums, for that particular aircraft system combination, lower than RVR 60m
(200ft) and 800m (1/2 statute mile) visibility above the lowest MDA/DH and
visibility/RVR minimums authorized for instrument approaches and landings at that
airport using area navigation systems.
CIVIL AVIATION
ADMINISTRATION
OF CHINA CCAR-121 / 135 OPERATIONS SPECIFICATIONS
CAAC DOCUMENT
APPROVAL NO
AC-121-001R1
(Company Name) C0029-2 Certificate No:
Effective Date: Y M D
1. Issued by (Branch Name) ,Regional Administration of CAAC
2. These Operations Specifications are approved by direction of CAAC
Principal Operations Inspector: (Name & Signature of POI)
3. Date Approval is effective (Y/M/D) Amendment Number:
4. The certificate holder hereby accepts and receives the Operations Specifications in this
paragraph.
Certificate Holder Representative: (Name & Signature)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：CCAR121_135 Operations Specifications(59)