曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

subcontracted parts, if their physical or chemical properties
cannot be readily and accurately determined;
(b) suitable storage and adequate protection of materials subject to
damage and deterioration;
(c) carrying out processes affecting the quality and safety of the
finished Class I, Class II, Class III or unapproved Class I product
in accordance with acceptable industry or Australian
specifications;
(d) inspecting parts and components, at points during the production
process at which accurate determinations can be made, to
determine whether:
(i) parts and components for a Class I product conform to the
type design data for the product; or
(ii) parts and components for a Class II, Class III or
unapproved Class I product conform to the product design
data for the product;
(e) ensuring that current design drawings are readily available to
manufacturing and inspection personnel, and used when
necessary;
(f) ensuring that design changes, including material substitutions,
are controlled before being incorporated in:
(i) a finished Class I product; or
(ii) a Class II, Class III or unapproved Class I product;
(g) segregating and identifying rejected materials and parts in a
manner that precludes installation in the finished Class I, Class
II, Class III or unapproved Class I product;
Civil Aviation Safety Regulations 1998 (CASR)
CASR – 1st Edition – January 2003 Office of Legal Counsel
Replacement Page – Amdt No. 5: Effective 27 November 2003 Civil Aviation Safety Authority
Part 21 — 59
(h) a system for processing through the Materials Review Board any
materials and parts that are withheld because of departures from
design data or specifications, and that are to be considered for
installation in a finished Class I, Class II, Class III or unapproved
Class I product;
(i) a system for identifying and reinspecting materials and parts
determined by the Materials Review Board to be serviceable if
rework or repair is necessary;
(j) maintaining inspection records, identified with the finished Class
I, Class II, Class III or unapproved Class I product where
practicable, and retaining them for at least 2 years.
Source FARs section 21.125 modified.
21.145 Materials Review Board
(1) The holder of a production certificate (other than a production
certificate referred to in subregulation 21.133 (2B)) must:
(a) establish a Materials Review Board (to include representatives
from the manufacturer’s inspection and engineering departments)
and materials review procedures; and
(b) maintain complete records of Materials Review Board action for
at least 2 years after the action was taken.
Penalty: 50 penalty units.
(2) An offence against subregulation (1) is an offence of strict liability.
Note For strict liability, see section 6.1 of the Criminal Code.
Source FARs section 21.125 modified.
21.147 Changes in quality system
(1) After the issue of a production certificate, each change to the quality
system is subject to review by CASA.
(2) The holder of a production certificate must immediately notify
CASA, in writing, of any change to the quality system that may
affect:
(a) the inspection of a Class I product being manufactured under the
certificate, or the conformity of such a product to its type design
data, or the airworthiness of such a product; or
(b) the inspection of an unapproved Class I product being
manufactured under the certificate, or the conformity of such a
product to its product design data, or the airworthiness of such a
product; or
(c) the inspection of a Class II or Class III product being
manufactured under the certificate, or the conformity of such a
product to its product design data.
Penalty: 50 penalty units.
(3) An offence against subregulation (2) is an offence of strict liability.
Note For strict liability, see section 6.1 of the Criminal Code.
Civil Aviation Safety Regulations 1998 (CASR)
Office of Legal Counsel CASR – 1st Edition – January 2003
Civil Aviation Safety Authority Replacement Page – Amdt No. 5: Effective 27 November 2003
Part 21 — 60
21.149 Multiple products
CASA may authorise more than 1 Class I, Class II, Class III or
unapproved Class I product to be manufactured under 1 production
certificate if the products have similar production characteristics.
Source FARs section 21.149 modified.
21.151 Production limitation record
A production certificate must include, or have attached to it, a
production limitation record that sets out:
(a) for a Class I product — the type certificate or foreign type
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：澳大利亞CASR Civil Aviation Safety Regulations上(71)