曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

4L key instead of the 3L key.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 5/58
FCOM 19 AUG 10
�� If the VHF3 SCAN SELECT menu can be accessed, and if no VHF Service Providers have
been selected :
The MCDU scratchpad displays the “ENTER VHF3 SCAN SELECT” message.
On the VHF3 SCAN SELECT page, select a Service Providers’ list, in the airline priority order,
and activate the VHF SCAN SELECT function.
Example : To select Service Providers SITA 725 and ARINC :
1. Press the 5L key : The star next to the ERASE indication disappears, then reappears.
2. Press the 1L key to select SITA 725 : The SELECT indication goes off, and the priority number
of selection # 1 appears.
3. Press the 1R key to select ARINC : The SELECT indication goes off, and the priority number
of selection # 2 appears.
4. Press the 5R key to activate the VHF SCAN SELECT function : The star next to the SCAN
SELECT LOAD indication disappears, then reappears.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 6/58
FCOM 19 AUG 10
Note: Modification of the SCAN SELECT setting may result in the loss of air-ground VHF datalink
communication. Therefore, the SCAN SELECT setting should not be modified by the crew,
unless they have been instructed to do so.
NOTIFICATION PROCEDURE AND CONNECTION
Applicable to:
Before connection, the DCDU screen appears as follows:
NOTIFICATION PROCEDURE :
Notification is made through the MCDU NOTIFICATION SD page:
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 7/58
FCOM 19 AUG 10
The FMGC provides the ATC FLT number.
The notification procedure is used by the ATC to correlate the aircraft with the ICAO flight number.
Consequently, it is essential to enter exactly the same number, shown on ICAO flight plan (with
the same number of letters), on the MCDU INIT SD page.
The ATC CENTER field defaults to the center, that was connected during the previous flight. It can
be changed, if applicable.
Note: 1. Once the ATC center has been notified (“NOTIFIED” is displayed on the MCDU
“NOTIFICATION” SD page), the ATC center will initiate the CPDLC and/or ADS-C
connection. Therefore, re-notifications should be avoided.
2. For ADS-C operations, check on the MCDU “CONNECTION STATUS” SD page that
the ADS-C is set to ON prior to performing a notification.
CONNECTION
Once notified, the connection is performed at the ATC’s discretion.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 8/58
FCOM 19 AUG 10
For operations in a CPDLC, or CPDLC and ADS environment:
When CPDLC connection is established, the “ACTIVE ‐ ATC” is displayed on the DCDU.
The pilot should verify that the appropriate ATC center is connected.
‐ For operations in an “ADS-C only” environment (NO CPDLC), “NO ACTIVE ATC” remains
displayed on the DCDU and does not reflect the ADS-C contract status.
This is due to the fact that the DCDU is the interface which sustains CPDLC communication,
whereas the ADS-C is an additional feature which is transparent to the crew.
NOTIFICATION PROCEDURE AND CONNECTION
Applicable to:
Before connection, the DCDU screen appears as follows:
NOTIFICATION PROCEDURE :
Notification is made through the MCDU NOTIFICATION SD page:
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 9/58
FCOM 19 AUG 10
The FMGC provides the ATC FLT number.
The notification procedure is used by the ATC to correlate the aircraft with the ICAO flight number.
Consequently, it is essential to enter exactly the same number, shown on ICAO flight plan (with
the same number of letters), on the MCDU INIT SD page.
The ATC CENTER field defaults to the center, that was connected during the previous flight. It can
be changed, if applicable.
Note: 1. Once the ATC center has been notified (“NOTIFIED” is displayed on the MCDU
“NOTIFICATION” SD page), the ATC center will initiate the CPDLC and/or ADS-C
connection. Therefore, re-notifications should be avoided.
2. For ADS-C operations, check on the MCDU “CONNECTION STATUS” SD page that
the ADS-C is set to ARMED prior to performing a notification.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A330/A340機組操作手冊 FLIGHT CREW OPERATING MANUAL FCOM 11(106)