(d)
Make sure that there is a clearance of 0.5 mm (0.0196 in.) to 3.0 mm (0.1181 in.) between the intermediate fairing (17) and the front fairing (20). If necessary, cut and de-burr the overlap at the rear of the front fairing (20) to get the correct dimension.
(e)
Install the assembly with the bolts (21).
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 28-21-49Page 430 1201-207, 1May 01/05 1 1 1CES 1 (f) TORQUE tighten the bolts (21) to 1.13 m.daN (99.99 lbf.in).
(5) Make sure that the guide (30), the bracket (34) and the clamp (33) are positioned correctly. TORQUE the nuts (31) on the bolts (32) to between 0.14 and 0.16 m.daN (12.38 and 14.15 lbf.in).
R **ON A/C 106-149, 228-299, 301-399, 401-499,
Subtask 28-21-49-420-050-C
B. Installation of the Inboard Fuel Pump Fairing NOTE : Install the inboard fuel pump fairing in this sequence:
____
-
the intermediate fairing (5)
-
the rear fairing (4)
-the front fairing (8) and the cover plate (11) assembly. NOTE : Sealant is not used between the fairings (8), (5) and (4) and the
____
lower wing skin.
(1)
Before you install the fairings, make sure that the length of the harness (27) is correct. Measure the distance between the front face of the connector (36) and the forward edge of the guide (30). The correct length of the inboard harness should be 1320 mm (51.9685 in.).
(2)
If necessary, adjust the length of the harness (27) as follows:
(a)
Loosen the nuts (32), the bolts (33) and the clamp (34) on the bracket (31) and the guide (30).
(b)
Carefully move the harness (27) through the guide (30), the clamp
(34)
and the conduit (35) to get the correct length.
(3)
Install the intermediate fairing (5) as follows:
(a)
Hold the intermediate fairing (5) in position near the lower wing skin.
(b)
Carefully push the harness (27) into the retention channel inside the intermediate fairing (5).
(c)
Make sure that the harness (27) is held correctly below the lips of the retention channel in the intermediate fairing (5).
NOTE : Make sure that the harness (27) is not in tension.
____
R 1EFF : 001-049, 051-099, 101-149, 151-154, 1 28-21-49Page 431 1201-207, 228-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(d)
Engage the key-hole slots in the intermediate fairing (5) with the wing skin bolts.
(e)
Move the intermediate fairing (5) forward to engage the bolts fully.
(f)
Make sure that the harness (27) is not caught between:
-
the key-hole slot positions on the intermediate fairing (5) and the wing skin
-
the edge of the intermediate fairing (5) and the wing skin.
(4) Install the rear fairing (4) as follows:
(a)
Make sure that the intermediate fairing (5) is correctly
installed and pushed tightly against its stop.
(b)
Hold the rear fairing (4) in position near the lower wing skin.
(c)
Carefully push the harness (27) into the retention channel inside the rear fairing (4).
(d)
Make sure that the harness (27) is held correctly below the lips of the retention channel in the rear fairing (4).
NOTE : Make sure that the harness (27) is not in tension.
____
(e)
Pull the harness (27) lightly in a rearwards direction. If necessary, push unwanted harness up through the guide (30) and the clamp (34) into the conduit (35).
(f)
Engage the key-hole slots in the rear fairing (4) with the wing skin bolts.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油3(51)
