-
the rear fairing (17)
-the front fairing (21) and the cover plate (24) assembly. NOTE : Sealant is not used between the fairings (21), (18) and (17) and
____
the lower wing skin.
(1)
Before you install the fairings, make sure that the length of the harness (27) is correct. Measure the distance between the front face of the connector (36) and the forward edge of the guide (30). The correct length of the outboard harness should be 1345 mm (52.9527 in.).
(2)
If necessary, adjust the length of the harness (27) as follows:
(a)
Loosen the nuts (32), the bolts (33) and the clamp (34) on the bracket (31) and the guide (30).
(b)
Carefully move the harness (27) through the guide (30), the clamp
(34)
and the conduit (35) to get the correct length.
(3)
Install the intermediate fairing (18) as follows:
(a)
Hold the intermediate fairing (18) in position near the lower wing skin.
(b)
Carefully push the harness (27) into the retention channel inside the intermediate fairing (18).
(c)
Make sure that the harness (27) is held correctly below the lips of the retention channel in the intermediate fairing (18).
NOTE : Make sure that the harness (27) is not in tension.
____
(d)
Engage the key-hole slots in the intermediate fairing (18) with the wing skin bolts.
(e)
Move the intermediate fairing (18) forward to engage the bolts fully.
R 1EFF : 106-149, 228-299, 301-399, 401-499, 1 28-21-49Page 435 1 1 Aug 01/05 1 1 1CES 1 (f) Make sure that the harness (27) is not caught between:
-
the key-hole slot positions on the intermediate fairing (18) and the wing skin
-
the edge of the intermediate fairing (18) and the wing skin.
(4) Install the rear fairing (17) as follows:
(a)
Make sure that the intermediate fairing (18) is correctly
installed and pushed tightly against its stop.
(b)
Hold the rear fairing (17) in position near the lower wing skin.
(c)
Carefully push the harness (27) into the retention channel inside the rear fairing (17).
(d)
Make sure that the harness (27) is held correctly below the lips of the retention channel in the rear fairing (17).
NOTE : Make sure that the harness (27) is not in tension.
____
(e)
Pull the harness (27) lightly in a rearwards direction. If necessary, push unwanted harness up through the guide (30) and the clamp (34) into the conduit (35).
(f)
Engage the key-hole slots in the rear fairing (17) with the wing skin bolts.
(g)
Move the rear fairing (17) forward to engage the bolts fully.
(h)
Make sure that the:
-forward end of the rear fairing (17) goes inside the intermediate fairing (18) (out-of-wind)
-
harness (27) is not caught between the key-hole slot positions on the rear fairing (17) and the wing skin
-
harness (27) is not caught between the edge of the rear fairing
(17) and the wing skin.
(i)
Make sure that there is a clearance of 3.0 mm (0.1181 in.) to 4.0 mm (0.1574 in.) between the rear fairing (17) and the intermediate fairing (18). If necessary, cut and de-burr the overlap at the rear of the intermediate fairing (17) to get the correct dimension.
(j)
Install the bolt (16), the bush (15) and the nut (14). Tighten the bolt (16).
R 1EFF : 106-149, 228-299, 301-399, 401-499, 1 28-21-49Page 436 1 1 Aug 01/05 1 1 1CES 1
(k) Fill the clearance between the rear fairing (17) and the intermediate fairing (18) with SEALANTS (Material No. 09-016).
(5) Install the front fairing (21) and the cover plate (24) assembly as follows:
(a)
Make sure that the intermediate fairing (18) and the rear fairing
(17)
are correctly installed.
(b)
If the front fairing (21) and the cover plate (24) have been disassembled, continue as follows:
1_ Install the front fairing (21) to the cover plate (24) with
the bolt (26), the washer (25) and the bush (19). Do not
tighten the bolt (26).
2_ Install the cover plate (24) (complete with the front fairing
(21)) to the lower wing skin with the bolts (22) and the
washers (23). Do not tighten the bolts (22).
3_ Make sure that the front fairing (21) aligns with the
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油3(53)
