(2)
 Install the new O-ring (11).

 (3)
 Install the reducer (10).

 (4)
 Install the sequence valve (Ref. TASK 28-21-45-400-003).

 1EFF : ALL 1 28-21-52Page 433 1 1 Aug 01/05 1 1 1CES 1 Subtask 28-21-52-420-057

 B. Preparation for Installation
 (1)
 Clean the component interfaces and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).

 (2)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Lubricate the new items that follow with FUELS (Material No. 01-001) or COMMON GREASE (Material No. 04-012):

 -
the sealing ring (12)

 -
the O-ring (17)

 -the O-ring (19). Subtask 28-21-52-420-052
 C. Installation of the Fuel Pump Canister 2QM(3QM)
 (1)
 Install the new sealing ring (12) and the new O-rings (17) and (19).

 (2)
 Engage the connectors (16) and (14), while you put the canister (15) in position.

 (3)
 Install the canister (15) with the screws (13).

 (4)
 Torque the screws (13) to between 0.5 and 0.6 m.daN (44.24 and 53.09 lbf.in).

 (5)
 Install the connectors (14) and (16), with the bolts (21) and the nuts (20).

 (6)
 Install the pipe (9).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-21-52Page 434 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

R  **ON A/C 301-399, 
R  Subtask 28-21-52-560-051-A 
R  A. Preparation for a Replacement Component 
R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ 
R  MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 
R  (1) Lubricate the new O-ring (17) with FUELS (Material No. 01-001) or 
R  COMMON GREASE (Material No. 04-012). 
R  (2) Install the new O-ring (17). 
R  (3) Install the reducer (18). 
R  (4) Install the check valve (Ref. TASK 28-21-43-400-002). 
R  Subtask 28-21-52-420-057-A 
R  B. Preparation for Installation 
R  (1) Clean the component interfaces and the adjacent areas with a 
R  MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS 
R  (Material No. 11-026). 
R  (2) Make sure that the parts retained from the removed component are 
R  clean and in the correct condition. 
R  (3) Do an inspection of the component interface and/or the adjacent area. 
R  (4) Lubricate the new items that follow with FUELS (Material No. 01-001) 
R  or COMMON GREASE (Material No. 04-012): 
R  - the sealing ring (11) 
R  - the O-ring (19) 
R  - the O-ring (33) 
R  - the O-ring (39). 

R 1EFF : 301-399, 1 28-21-52Page 435 1 1 May 01/04 1 1 1CES 1

R  Subtask 28-21-52-420-052-A 
R  C. Installation of the Fuel Pump Canister 2QM(3QM) 
R  (1) Install the new sealing ring (11) and the new O-rings (19), (33) and 
R  (39). 
R  (2) Install the canister (15) with the screws (12). 
R  (3) Torque the screws (12) to between 0.5 and 0.6 m.daN (44.24 and 53.09 
R  lbf.in). 
R  (4) Install the connector (13). Install the bolts (40) and the nuts (38). 
R  (5) Install the bolt (41), the bonding tab (36) and the nut (37) 
R  (Ref. TASK 20-28-00-912-002). 
R  (6) Install the connector (14). Install the bolts (34) and the nuts (31). 
R  (7) Install the bolt (35), the bonding tab (29) and the nut (30) 
R  (Ref. TASK 20-28-00-912-002). 
R  (8) Install the connector (16). Install the bolts (22) and the nuts (21). 
R  (9) Install the fuel pipes that you removed (Ref. TASK 28-00-00-400-001). 
R  (10) Install the pipe (9). 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油3(79)