B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 49-16-00-710-002 Operational Test of the Air Intake Flap and Diverter
(APS 3200) 49-16-43-400-002 Installation of the Air Intake Flap (APS 3200) 49-16-44-400-002 Installation of the Air Intake Nose (APS 3200) 52-41-00-010-001 Open the APU Doors for Access 52-41-00-410-001 Close the APU Doors after Access 49-16-42-991-002 Fig. 401
3. Job Set-up
__________
Subtask 49-16-42-860-051
A. Aircraft Maintenance Configuration
(1)
Make sure that the aircraft electrical circuits are energized (Ref. TASK 24-41-00-861-002).
(2)
On the panel 25VU, make sure that the APU MASTER SW pushbutton switch is off.
(3)
Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.
(4)
Make sure that hydraulic systems are depressurized
(Ref. TASK 29-00-00-864-001).
(5)
Make sure that the access platform is in position below the APU compartment.
(6)
Make sure that the APU access doors are open (Ref. TASK 52-41-00-010-001).
(7)
Make sure that the LIGHT control switch 11LJ is set to the on position.
(8)
Make sure that the access door 314AR is open. Subtask 49-16-42-865-054
B.
Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
4. Procedure
_________
(Ref. Fig. 401/TASK 49-16-42-991-002) Subtask 49-16-42-420-052
A. Installation of the Air Intake Duct
(1)
Put the air intake duct (1) into position and hold it.
(2)
Install the bolt (6) and the bolts (5) and (3) and the washers (4) and (2).
(3)
Install the top flange (20) and the bottom flange (29) around the air intake duct (1).
(4)
Install the bolts (26) and the washers (27). Do not fully tighten the bolts at this time.
(5)
Install the bolts (24) and the washers (23). Do not fully tighten the bolts at this time.
(6)
Install the bolts (18) and the washers (19) to the anchor nuts. Tighten all screws and bolts.
(7)
Install the seal (13) on the flange (14) and install the distance washers (32) at the lower holes of the seal.
(8)
Install the frame (12) on the flange (14).
(9)
Apply SEALANTS (Material No. 09-016):
-to fill gaps which remain in the area of the flange (14) and the frame of the air intake duct (1).
(10)
Install the bolts (10), the washers (11) (15) and the nuts (16). Tighten the bolts equally.
(11)
Install the flange (14) with the screws (28), the washer (30) and the nuts (31) on the air intake duct (1).
(12)
Apply SEALANTS (Material No. 09-016) to all locations from which the sealant was removed.
(13)
Seal the bonding connections with SEALANTS (Material No. 09-016) and then apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001).
(14)
Install the air intake nose (Ref. TASK 49-16-44-400-002).
(15)
Install the air intake flap (Ref. TASK 49-16-43-400-002).
(16)
Apply SPECIAL MATERIALS (Material No. 05-005) around the screw heads at the inner side of the air intake duct.
Subtask 49-16-42-865-055
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.
Subtask 49-16-42-710-051
C. Do the operational test of the Air Intake Flap and Diverter (Ref. TASK 49-16-00-710-002).
5. Close-up
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3(11)
